4308-0 Peregrine Semiconductor, 4308-0 Datasheet

no-image

4308-0

Manufacturer Part Number
4308-0
Description
KIT EVAL FOR 4308 RF DSA
Manufacturer
Peregrine Semiconductor
Series
UltraCMOS™r
Type
Attenuatorr
Datasheet

Specifications of 4308-0

Frequency
0Hz ~ 4GHz
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
PE4308
Other names
4308-00
Product Description
The PE4308 is a high linearity, 5-bit RF Digital Step Attenuator
(DSA) covering 31 dB attenuation range in 1dB steps, and is
pin compatible with the PE430x series. This 75-ohm RF DSA
provides both parallel (latched or direct mode) and serial
CMOS control interface, operates on a single 3-volt supply and
maintains high attenuation accuracy over frequency and
temperature. It also has a unique control interface that allows
the user to select an initial attenuation state at power-up. The
PE4308 exhibits very low insertion loss and low power
consumption. This functionality is delivered in a 4x4 mm QFN
footprint.
The PE4308 is manufactured on Peregrine’s UltraCMOS™
process, a patented variation of silicon-on-insulator (SOI)
technology on a sapphire substrate, offering the performance
of GaAs with the economy and integration of conventional
CMOS.
Figure 1. Functional Schematic Diagram
Table 1. Electrical Specifications @ +25°C, V
Notes: 1. Device Linearity will begin to degrade below 1 MHz
Document No. 70-0162-04 │ www.psemi.com
Power-Up Control
Operation Frequency
Insertion Loss
Attenuation Accuracy
1 dB Compression3,4
Input IP3
Return Loss
Switching Speed
Parallel Control
Serial Control
2. See figures on Pages 4 to 6 for data across frequency.
3. Note Absolute Maximum in Table 3.
4. Measured in a 50 Ω system.
Parameter
RF Input
1,2,4
2
5
3
2
Two-tone inputs up to
50% control to 0.5 dB
Test Conditions
Switched Attenuator Array
Any Bit or Bit
Combination
of final value
Control Logic Interface
+18 dBm
1 MHz ≤ 1.2 GHz
1 MHz ≤ 1.2 GHz
DC ≤ 1.2 GHz
DC ≤ 1.2 GHz
DC ≤ 1.2 GHz
Frequency
DD
= 3.0 V
RF Output
Minimum
DC
30
10
-
-
-
-
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Figure 2. Package Type
Features
20 Lead 4x4 mm QFN
75 Ω RF Digital Attenuator
5-bit, 31 dB, DC – 4.0 GHz
Typical
Product Specification
PE4308
Attenuation: 1 dB steps to 31 dB
Flexible parallel and serial programming
interfaces
Latched or direct mode
Unique power-up state selection
Positive CMOS control logic
High attenuation accuracy and linearity
over temperature and frequency
Very low power consumption
Single-supply operation
75 Ω impedance
Pin compatible with PE430x series
Packaged in a 20 Lead 4x4 mm QFN
1.4
34
52
13
-
-
±(0.2 + 4% of atten setting)
Not to Exceed +0.4 dB
Maximum
2000
1.95
1
-
-
-
Page 1 of 11
Units
MHz
dBm
dBm
dB
dB
dB
dB
s

Related parts for 4308-0

4308-0 Summary of contents

Page 1

... Product Description The PE4308 is a high linearity, 5-bit RF Digital Step Attenuator (DSA) covering 31 dB attenuation range in 1dB steps, and is pin compatible with the PE430x series. This 75-ohm RF DSA provides both parallel (latched or direct mode) and serial CMOS control interface, operates on a single 3-volt supply and maintains high attenuation accuracy over frequency and temperature ...

Page 2

... ESD, precautions should be taken to avoid exceeding the rate specified in Table 3. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. Switching Frequency or DC blocked with an The PE4308 has a maximum 25 kHz switching rate. DC DD. Resistor on Pin 1 & bypass and kΩ resistor on the inputs to Pin 1 & 3 (see Figure 5) will eliminate package resonance between the RF input pin and the two digital inputs ...

Page 3

... PE4308 Product Specification Evaluation Kit The Digital Attenuator Evaluation Kit was designed to ease customer evaluation of the PE4308 DSA used in conjunction with the supplied DC cable to supply V , GND, and – use of the internal DD DD negative voltage generator is desired, then connect –V (black banana plug) to ground external – desired, then apply -3 V ...

Page 4

... Figure 9. Output Return Loss at Major 0 -10 -20 -30 -40 -50 1500 2000 0 Document No. 70-0162-04 │ UltraCMOS™ RFIC Solutions Product Specification 31dB 16dB 2dB 1dB 8dB 4dB 500 1000 1500 RF Frequency (MHz) Attenuation Steps (Zo=75 ohms) 500 1000 1500 RF Frequency (MHz) PE4308 2000 2000 ...

Page 5

... PE4308 Product Specification Typical Performance Data (25°C, V Figure 10. Attenuation Error Vs. Frequency 0.5 0 -0 500 1000 RF Frequency (MHz) Figure 12. Attenuation Error Vs. Attenuation Setting 0.4 0.2 0 -0.2 -0.4 -0.6 -0 Attenuation Setting (dB) Note: Positive attenuation error indicates higher attenuation than target value Document No. 70-0162-04 │ www.psemi.com = 3 ...

Page 6

... Peregrine Semiconductor Corp. All rights reserved. Page 3.0 V unless otherwise noted) DD Figure 15. Input 1 dB Compression (Zo=50 ohms) 1.2GHz, -40C 1.2GHz, 25C 1.2GHz, 85C 1500 2000 Product Specification 500 1000 RF Frequency (MHz) Document No. 70-0162-04 │ UltraCMOS™ RFIC Solutions PE4308 1500 2000 ...

Page 7

... Note: Not all 32 possible combinations of C1-C16 are shown. Serial Interface The PE4308’s serial interface is a 6-bit serial-in, parallel-out shift register buffered by a transparent latch. The latch is controlled by three CMOS- compatible signals: Data, Clock, and Latch Enable (LE). The Data and Clock inputs allow data to be Document No. 70-0162-04 │ ...

Page 8

... C, unless otherwise specified A Parameter Min LE minimum pulse width 10 LEPW Data set-up time before 10 PDSUP rising edge of LE Data hold time after 10 PDHLD falling edge of LE Document No. 70-0162-04 │ UltraCMOS™ RFIC Solutions PE4308 Product Specification ↑ LSB (last in) Max Unit ...

Page 9

... PE4308 Product Specification Figure 19. Package Drawing 0.435 0.18 DETAIL A 1. Dimension applies to metallized terminal and is measured between 0.25 and 0.30 from terminal tip. 2. Coplanarity applies to the exposed heat sink slug as well as the terminals. 3. Dimensions are in millimeters. Document No. 70-0162-04 │ www.psemi.com 4.00 2 ...

Page 10

... Figure 20. Marking Specifications Figure 21. Tape and Reel Drawing Table 10. Ordering Information Order Code Part Marking 4308-01 4308 4308-02 4308 4308-00 PE4308-EK 4308-51 4308 4308-52 4308 ©2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 4308 YYWW ZZZZZ YYWW = Date Code ZZZZZ = Last five digits of PSC Lot Number ...

Page 11

... PE4308 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation 9450 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 Europe Peregrine Semiconductor Europe Bâtiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 Space and Defense Products ...

Related keywords