DC1414B-B Linear Technology, DC1414B-B Datasheet - Page 12

• Manufacturer Part Number: DC1414B-B
• Description: BOARD EVAL LTM4601AHV
• Manufacturer: Linear Technology
• Series: µModuler

Specifications of DC1414B-B

• Design Resources: LTM4601AHV Spice Model LTM4601AHV Gerber Files DC1414B Design Files DC1414B Schematic
• Main Purpose: DC/DC, Step Down
• Outputs And Type: 1, Non-Isolated
• Power - Output: -
• Voltage - Output: 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V
• Current - Output: 12A
• Voltage - Input: 5 ~ 28 V
• Regulator Topology: Buck
• Frequency - Switching: 850kHz
• Board Type: Fully Populated
• Utilized Ic / Part: LTM4601AHV
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

LTM4601AHV
APPLICATIONS INFORMATION
Multiphase operation with multiple LTM4601AHV devices
in parallel will lower the effective output ripple current due
to the interleaving operation of the regulators. For example,
each LTM4601AHV’s inductor current of a 12V to 2.5V
multiphase design can be read from the Inductor Ripple
12
12
10
8
6
4
2
0
0
Figure 3. Inductor Ripple Current vs Duty Cycle
Figure 4. Normalized Output Ripple Current vs Duty Cycle, Dlr = V
20
DUTY CYCLE (V
40
OUT
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.65
0.60
0.55
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
/V
0
IN
0.1 0.15 0.2 0.25
60
)
4601AHV F03
80
0.3
2.5V OUTPUT
5V OUTPUT
1.8V OUTPUT
1.5V OUTPUT
1.2V OUTPUT
3.3V OUTPUT WITH
130k ADDED FROM
V
5V OUTPUT WITH
100k ADDED FROM
f
SET
OUT
0.35
TO GND
TO f
SET
0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9
DUTY CYCLE (V
Current versus Duty Cycle graph (Figure 3). The large
ripple current at low duty cycle and high output voltage
can be reduced by adding an external resistor from f
ground which increases the frequency. If the duty cycle is
DC = 2.5V/12V = 0.21, the inductor ripple current for 2.5V
output at 21% duty cycle is ~6A in Figure 3.
Figure 4 provides a ratio of peak-to-peak output ripple cur-
rent to the inductor current as a function of duty cycle and
the number of paralleled phases. Pick the corresponding
duty cycle and the number of phases to arrive at the correct
output ripple current ratio value. If a 2-phase operation is
chosen at a duty cycle of 21%, then 0.6 is the ratio. This
0.6 ratio of output ripple current to inductor ripple of 6A
equals 3.6A of effective output ripple current. Refer to Ap-
plication Note 77 for a detailed explanation of output ripple
current reduction as a function of paralleled phases.
The output voltage ripple has two components that are
related to the amount of bulk capacitance and effective
series resistance (ESR) of the output bulk capacitance.
O
/V
IN
)
O
T/L
I
, Dlr = Each Phase’s Inductor Current
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
4601AHV F04
4601ahvfa
SET
to