VHB150W-Q48-S5 CUI Inc, VHB150W-Q48-S5 Datasheet
![no-image](/images/manufacturer_photos/0/1/176/cui_inc_sml.jpg)
VHB150W-Q48-S5
Specifications of VHB150W-Q48-S5
VHB150W-Q48-S5
Related parts for VHB150W-Q48-S5
VHB150W-Q48-S5 Summary of contents
Page 1
... On/Off control make these converters very useful in many applications. MODEL VHB150W-Q24-S3R3 VHB150W-Q24-S5 VHB150W-Q24-S12 VHB150W-Q24-S15 VHB150W-Q24-S24 VHB150W-Q48-S3R3 VHB150W-Q48-S5 VHB150W-Q48-S12 VHB150W-Q48-S15 VHB150W-Q48-S24 notes: 1. see output derating (page 4) 2. input currents are measured at nominal input voltage 3. efficiency is measured at nominal line, full load INPUT parameter ...
Page 2
... PART NUMBER: VHB150W OUTPUT parameter conditions/description voltage accuracy transient response 25% step load change external trim adj. range ripple & noise (20MHz BW) 3.3V, 5V 12V& 15V 24V temperature coefficient short circuit protection continuous line regulation 5 6 load regulation over voltage protection trip range nom. ...
Page 3
... PART NUMBER: VHB150W MECHANICAL DRAWING th 20050 SW 112 Ave. Tualatin, Oregon 97062 DESCRIPTION: half-brick dc-dc converter phone phone 503.612.2300 fax fax 503.612.2383 page date 08/2009 www.v-infinity.com ...
Page 4
... APPLICATION NOTES 1. OUTPUT DE-RATING The operating case temperature range for VHB150W is -40 ~ +100°C. When operating the VHB150W series, proper derating or cooling is needed. The maximum case temperature under any operating condition should not exceed 100°C. Power Dissipated vs Ambient Temperature and Air Flo w Ambient Temperature ,Ta(Deg ...
Page 5
... The fuse rating will depend on the input range and should allow for the maximum current at the lowest input volt- age, as shown in this equation: Ipeak = 150%*Pout/(η η *Vmin). In the previous example of VHB150W-Q24-S5, the peak input current at 9V was calculated to be 28. fuse may be suitable for this application. Make sure the fuse voltage rating is higher than the maximum input voltage. ...
Page 6
... R load R trim- Ω Where: R the nominal output voltage the desired output voltage. R1 and R2 are internal to the unit and are defined in Table 2. For example, to trim-down the output voltage of 5.0V module is calculated (VHB150W-Q48-S5 4.6V, R trim-up = 3.3 kΩ – 9.18kΩ R2 (Kohm) 7.2 3 ...
Page 7
... PART NUMBER: VHB150W 10. OUTPUT OCP AND SHORT-CIRCUIT PROTECTION Output overload and short circuit conditional will cause the output voltage to decline or shutdown altogether. is not over 100°C, the output recovers automatically when the short or OCP conditions are removed. In the case of slight overloading, the output voltage may not shut down, but the converter may build up heat over time, causing over-temperature shutdown ...
Page 8
... PART NUMBER: VHB150W 14. OUTPUT SERIES CONNECTIONS Two or more converters can be connected in series to obtain a higher output voltage. To prevent output reverse biasing each other in case of a short, add a Schottky diode on each output in reverse polarity, as shown in the diagram. In the event of a short, the con- verters will forward-bias the diodes and the output reversal will be limited to one diode drop (about 0 ...
Page 9
... PART NUMBER: VHB150W 17. OUTPUT FILTERING The converter has built-in capacitors at the output to control ripple and noise. If desired, additional output capacitance can be introduced at the input to the powered equipment. Recommended starting point: one 10μF tantalum and one 1μF ceramic capacitor in parallel at the output. ...