R88M-W3K030T-BS2 Omron, R88M-W3K030T-BS2 Datasheet - Page 246
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
R88M-W3K030T-BS2
Manufacturer Part Number
R88M-W3K030T-BS2
Description
SERVO MOTOR 3KW 200V W/BRAKE
Manufacturer
Omron
Datasheet
1.R88A-PR02W.pdf
(458 pages)
Specifications of R88M-W3K030T-BS2
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R88MW3K030TBS2
- Current page: 246 of 458
- Download datasheet (5Mb)
Operation
D Setup when Replacing Battery Unit
Note It is not necessary to set up and reset the initial parameters for the Motion Control Unit if no alarm
D Other Cases where Setup Is Required
4-3
4-3-1 Operation Details
4-8
• If an alarm (A.81) occurs after replacing the Battery Unit, repeat the setup from the start.
• When connecting to the CV500-MC221/421 or C200H-MC221 Motion Control Unit, carry out the set-
• If the Encoder Cable is removed from the connector (on either the Servo Driver or Servomotor side),
• If the Battery Unit has completely worn down, the data within the absolute encoder will be cleared. In
• The key operations for the R88A-PR02W Parameter Unit and the Servo Driver front panel setting
• If a Parameter Unit is connected, the indicators (7-segment LEDs) on the front panel will flash, and
up close to the mechanical origin (This limitation does not apply to the CS1W-MC221/MC241 Motion
Control Unit). The rotation data will be different from before the battery was replaced, so reset the
initial Motion Control Unit parameters (including for the CS1W-MC221/MC421 Motion Control Unit).
the data within the absolute encoder will be cleared. In this case, perform the setup once again.
this case, replace the Battery Unit and perform the setup once again.
keys vary depending on the functions used. The same settings and operations are possible with ei-
ther method.
the settings keys cannot be used.
occurs after the Battery Unit has been replaced. If the Battery Unit is replaced using the correct
procedure before it wears out, an error alarm will not be generated. Refer to 4-2-2 Absolute En-
coder Setup and Battery Changes for Battery Unit service life and replacement method.
This section explains basic operations and the jog operation for the Servomotor and
Servo Driver.
Trial Operation
Chapter 4
Related parts for R88M-W3K030T-BS2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: