R88M-W3K030H-BS2 Omron, R88M-W3K030H-BS2 Datasheet - Page 230
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
R88M-W3K030H-BS2
Manufacturer Part Number
R88M-W3K030H-BS2
Description
SERVOMOTOR 3KW 3000RPM INC BK KE
Manufacturer
Omron
Datasheet
1.R88A-PR02W.pdf
(458 pages)
Specifications of R88M-W3K030H-BS2
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
R88MW3K030HBS2
- Current page: 230 of 458
- Download datasheet (5Mb)
System Design and Installation
• When installing noise filters for Encoder Cables, use clamp filters. The following table shows the rec-
• Do not place the Encoder Cable in the same duct as Power Cables and Control Cables for brakes,
H Improving Control I/O Signal Noise Resistance
Positioning can be affected if control I/O signals are influenced by noise. Follow the methods outlined
below for the power supply and wiring.
• Use completely separate power supplies for the control power supply (especially 24 V DC) and the
• As much as possible, keep the power supply for pulse command and deviation counter reset input
• It is recommended that a line driver be used for pulse command and deviation counter reset outputs.
• Always use twisted-pair shielded cables for pulse command and deviation counter reset signal lines,
• Always use twisted-pair shielded cable for speed and torque command signal lines, and connect both
• If the control power supply wiring is long, noise resistance can be improved by adding 1-μF laminated
• For encoder output (phase-A, -B, and -Z) lines, be sure to use twisted-pair shielded cable, and con-
• For open-collector specifications, keep the length of wires to within two meters.
3-36
NEC TOKIN
TDK
ommended clamp filter models.
solenoids, clutches, and valves.
external operation power supply. In particular, be careful not to connect the two power supply ground
wires. Install a noise filter on the primary side of the control power supply.
lines separate from the control power supply. Be particularly careful not to connect the two power sup-
ply ground lines.
and connect both ends of the shield to frame grounds.
ends of the shield to frame grounds.
ceramic capacitors between the control power supply and ground at the Servo Driver input section or
the controller output section.
nect both ends of the shield to frame grounds.
Maker
EMI core
Clamp filter
p
Name
ESD-SR-25
ZCAT2032-0930
ZCAT3035-1330
ZCAT2035-0930A
Model
Chapter 3
Related parts for R88M-W3K030H-BS2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6D-1A-ASI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G8P-1A4P](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: