DS2406 Maxim Integrated Products, DS2406 Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS2406
Manufacturer Part Number
DS2406
Description
IC SW DL ADDRESS W/1K MEM TO-92
Manufacturer
Maxim Integrated Products
Datasheet
1.DS2406.pdf
(32 pages)
Specifications of DS2406
Applications
Remote Control, Remote Metering
Interface
1-Wire
Voltage - Supply
2.8 V ~ 6 V
Package / Case
TO-92-3 (Standard Body), TO-226
Mounting Type
Through Hole
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS2406
Manufacturer:
DALLAS
Quantity:
5 510
Company:
Part Number:
DS2406
Manufacturer:
Dallas
Quantity:
213
Part Number:
DS2406
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS2406+
Manufacturer:
Maxim
Quantity:
164
Part Number:
DS2406P
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS2406P+
Manufacturer:
NXP
Quantity:
3 978
Part Number:
DS2406P+
Manufacturer:
MAXIM/美信
Quantity:
20 000
TWO-CHANNEL WRITE Figure 10c
1-WIRE
PIO-A
PIO-B
PIO-A
PIO-B
1-WIRE BUS SYSTEM
The 1-Wire bus is a system, which has a single bus master and one or more slaves. In all instances, the
DS2406 is a slave device. The bus master is typically a microcontroller. The discussion of this bus
system is broken down into three topics: hardware configuration, transaction sequence, and 1-Wire
signaling (signal types and timing). A 1-Wire protocol defines bus transactions in terms of the bus state
during specified time slots that are initiated on the falling edge of sync pulses from the bus master.
HARDWARE CONFIGURATION
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have an
open drain or 3-state outputs. The 1-Wire port of the DS2406 is open drain with an internal circuit
equivalent to that shown in Figure 11. Typical bus master ports are shown in Figure 12. If a bi-directional
pin is not available, separate output and input pins can be tied together. A multidrop bus consists of a 1-
Wire bus with multiple slaves attached. The 1-Wire bus has a maximum data rate of 15.4kbits/s. For
normal communication excluding EPROM programming the 1-Wire bus requires only a pull-up resistor
of approximately 5kΩ for short line lengths.
The idle state for the 1-Wire bus is high. If, for any reason a transaction needs to be suspended, the bus
MUST be left in the idle state if the transaction is to resume. If this does not occur and the bus is left low
for more than 120µs, one or more of the devices on the bus may be reset. If the 1-Wire bus remains low
for more than 5ms any DS2406 that is not V
both PIOs.
TRANSACTION SEQUENCE
The sequence for accessing the DS2406 via the 1-Wire port is as follows:
Initialization
ROM Function Command
Memory or Channel Access Function Command
Transaction/Data
IC=0, ASYNCHRONOUS MODE
IC=1, SYNCHRONOUS MODE
td1
A1
A1
15 µs < td1 < 60 µs
B1
B1
B1
A1
A2
A2
td0
B2
CC
200 ns < td0 < 300 ns
17 of 32
powered may perform a power-on reset and switch off
B2
B2
A2
A3
A3
B3
A3
B3
B3
A4
A4
B4
A4
B4
B4