PDI1394P25BD-T ST-Ericsson Inc, PDI1394P25BD-T Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/6/627/st-ericsson_inc_sml.jpg)
PDI1394P25BD-T
Manufacturer Part Number
PDI1394P25BD-T
Description
IC IEEE 1394 LINK CTRLR 64LQFP
Manufacturer
ST-Ericsson Inc
Datasheet
1.PDI1394P25BD.pdf
(45 pages)
Specifications of PDI1394P25BD-T
Applications
AV,TV, VTR
Interface
IEEE 1394
Voltage - Supply
3 V ~ 3.6 V
Package / Case
64-LQFP
Mounting Type
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PDI1394P25BD-T
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Philips Semiconductors
5.0 PIN DESCRIPTION
2001 Sep 06
AGND
AV
BRIDGE
C/LKON
CNA
CPS
CTL0,
CTL1
1-port 400 Mbps physical layer interface
Name
DD
CMOS 5 V tol
CMOS 5 V tol
Pin Type
Supply
Supply
CMOS
CMOS
CMOS
Numbers
32, 33,
39, 48,
49, 50
30, 31,
42, 51,
52
28
19
3
24
4
5
LQFP
Pin
Numbers
A1, A5,
A8, B1,
B2, B7
B8, C2,
C3, C5,
C7, D2
D6
F6
F3
E5
G3
G4
LFBGA
Ball
I/O
I/O
I/O
—
—
O
I
I
Analog circuit ground terminals. These terminals should be tied together
to the low impedance circuit board ground plane.
Analog circuit power terminals. A combination of high frequency
decoupling capacitors on each side are suggested, such as paralleled
0.1 F and 0.001 F. These supply terminals are separated from
PLLV
should be tied at a low impedance point on the circuit board.
BRIDGE input. This input is used to set the Bridge_Aware bits located in
the Vendor-Dependent register Page 7, base address 1001
positions 6 and 7. This pin is sampled during a hardware reset (RESET
low). When the BRIDGE pin is tied low (or through a 1 k resistor to
accommodate other vendor’s pin-compatible chips), the Bridge_Aware
bits are set to “00” indicating a “non-bridge device.” When the BRIDGE
pin is tied high, the Bridge_Aware bits are set to “11” indicating a “1394.1
bridge compliant” device. The default setting of the Bridge_Aware bits
can be overridden by writing to the register. The Bridge_Aware bits are
reported in the self-ID packet at bit positions 18 and 19.
Bus Manager Contender programming input and link-on output. On
hardware reset, this terminal is used to set the default value of the
contender status indicated during self-ID. Programming is done by tying
the terminal through a 10-k resistor to a high (contender) or low (not
contender). The resistor allows the link-on output to override the input.
If this pin is connected to a LLC driver pin for setting Bus Manager/IRM
contender status, then a 10-k series resistor should be placed on this
line between the PHY and the LLC to prevent possible contention. In this
case. the pull-high or pull-low resistors mentioned in the previous
paragraph should not be used. Refer to Figure 9.
Following hardware reset, this terminal is the link-on output, which is
used to notify the LLC to power-up and become active. The link-on
output is a square-wave signal with a period of approximately 163 ns (8
SYSCLK cycles) when active. The link-on output is otherwise driven low,
except during hardware reset when it is high impedance.
The link-on output is activated if the LLC is inactive (LPS inactive or the
LCtrl bit cleared) and when:
a) the PHY receives a link-on PHY packet addressed to this node,
b) the PEI (port-event interrupt) register bit is 1, or
c) any of the CTOI (configuration-timeout interrupt), CPSI
Once activated, the link-on output will continue active until the LLC
becomes active (both LPS active and the LCtrl bit set). The PHY also
deasserts the link-on output when a bus-reset occurs unless the link-on
output would otherwise be active because one of the interrupt bits is set
(i.e., the link-on output is active due solely to the reception of a link-on
PHY packet).
NOTE: If an interrupt condition exists which would otherwise cause the
link-on output to be activated if the LLC were inactive, the link-on output
will be activated when the LLC subsequently becomes inactive.
Cable Not Active output. This terminal is asserted high when there are
no ports receiving incoming bias voltage.
Cable Power Status input. This terminal is normally connected to cable
power through a 390 k resistor. This circuit drives an internal
comparator that is used to detect the presence of cable power.
Control I/Os. These bi-directional signals control communication
between the PDI1394P25 and the LLC. Bus holders are built into
these terminals.
5
(cable-power-status interrupt), or STOI (state-timeout interrupt)
register bits are 1 and the RPIE (resuming-port interrupt enable)
register bit is also 1.
DD
and DV
DD
internal to the device to provide noise isolation. They
Description
PDI1394P25
Preliminary data
b
, bit