AD9888KS-100 Analog Devices Inc, AD9888KS-100 Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9888KS-100
Manufacturer Part Number
AD9888KS-100
Description
IC FLAT PANEL INTERFACE 128-MQFP
Manufacturer
Analog Devices Inc
Datasheet
1.AD9888KSZ-205.pdf
(32 pages)
Specifications of AD9888KS-100
Rohs Status
RoHS non-compliant
Applications
Graphic Cards, VGA Interfaces
Interface
2-Wire Serial
Voltage - Supply
3 V ~ 3.6 V
Package / Case
128-MQFP, 128-PQFP
Mounting Type
Surface Mount
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9888KS-100
Manufacturer:
A/D
Quantity:
156
Company:
Part Number:
AD9888KS-100
Manufacturer:
ADI
Quantity:
442
Part Number:
AD9888KS-100
Manufacturer:
ADI/亚德诺
Quantity:
20 000
MODE CONTROL 1
15
15
15
15
REV. B
PARALLEL
0
1
DEMUX
0
1
7
A bit that determines whether all pixels are presented to a
single port (A), or alternating pixels are demultiplexed to
Ports A and B.
When DEMUX = 0, Port B outputs are in a high
impedance state. The maximum data rate for single-port
mode is 110 MHz. The timing diagrams starting with
Figure 13 show the effects of this option.
The power-up default value is 1.
6
A bit that determines whether all pixels are presented to
Port A and Port B simultaneously on every second
DATACK rising edge, or alternately on Port A and
Port B on successive DATACK rising edges.
When in single port mode (DEMUX = 0), this bit is
ignored. The timing diagrams (Figure 17) show the effects
of this option.
The power-up default value is PARALLEL = 1.
5
One bit that determines whether even pixels or odd pixels
go to Port A.
In normal operation (OUTPHASE = 0) when operating
in dual-port output mode (DEMUX = 1), the first sample
after the Hsync leading edge is presented at Port A. Every
subsequent ODD sample appears at Port A. All EVEN
samples go to Port B.
When OUTPHASE = 1, these ports are reversed and the
first sample goes to Port B.
When DEMUX = 0, this bit is ignored as data always
comes out of only Port A.
4
A bit that configures the output data in 4:2:2 mode. This
mode can be used to reduce the number of data lines used
Table XXXV. Output Port Phase Settings
OUTPHASE
0
1
Channel Mode
Table XXXIII. Channel Mode Settings
Output Mode
Output Port Phase
4:2:2 Output Mode Select
Table XXXIV. Output Mode Settings
Function
All data goes to Port A.
Alternate pixels go to Port A and Port B.
Function
Data is interleaved.
Data is simultaneous on every other
data clock.
First Pixel after Hsync
Port A
Port B
–25–
15
15
15
Channel
Red
Green
Blue
from 24 down to 16 for applications using YUV, YCbCr,
or YPbPr graphics signals. A timing diagram for this mode
is shown in Figure 12. Recommended input and output
configurations are shown in Table XXXVII. In 4:2:2
mode, the red and blue channels can be interchanged to
help satisfy board layout or timing requirements, but the
green channel must be configured for Y.
3
A bit that selects either analog inputs from Channel 0 or
the analog inputs from Channel 1.
2-1
Two bits that select the analog bandwidth.
0
A bit that determines the source of the pixel clock.
A Logic 0 enables the internal PLL that generates the
pixel clock from an externally provided HSYNC.
A Logic 1 enables the external CKEXT input pin. In this
mode, the PLL Divide Ratio (PLLDIV) is ignored. The
clock phase adjust (PHASE) is still functional.
The power-up default value is EXTCLK = 0.
Table XXXVII. 4:2:2 Input/Output Configuration
EXTCLK
0
1
Table XXXIX. Analog Bandwidth Control
Table XL. External Clock Select Settings
Table XXXVI. 4:2:2 Output Mode Select
Input Mux Control
Analog Bandwidth Control
External Clock Select
Table XXXVIII. Input Mux Control
Bit 2
1
1
0
0
Control
0
1
Select
0
1
Input Connection
V
Y
U
Bit 1
1
0
1
0
Function
Internally Generated Clock
Externally Provided Clock Signal
Channel Selected
Channel 0
Channel 1
Analog Bandwidth
500 MHz
300 MHz
150 MHz
75 MHz
Output Mode
4:4:4
4:2:2
High Impedance
Output Format
U/V
Y
AD9888