AD7669JR Analog Devices Inc, AD7669JR Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD7669JR
Manufacturer Part Number
AD7669JR
Description
IC I/O PORT 8BIT ANLG 28-SOIC
Manufacturer
Analog Devices Inc
Series
LC²MOSr
Datasheet
1.AD7569JRZ.pdf
(20 pages)
Specifications of AD7669JR
Rohs Status
RoHS non-compliant
Applications
Analog I/O
Interface
Bus
Voltage - Supply
4.75 V ~ 5.25 V
Package / Case
28-SOIC (7.5mm Width)
Mounting Type
Surface Mount
Converter Type
ADC/DAC
Resolution
8b
Data Rate
0.5MSPS
Digital Interface Type
Parallel
Pin Count
28
Package Type
SOIC W
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7669JR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7669JRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
PIN FUNCTION DESCRIPTION
(Applies to the AD7569 and AD7669 unless otherwise stated.)
Pin
Mnemonic
AGND
V
(V
V
RANGE
RESET
DB7
DB6–DB2
DGND
DB1
DB0
WR
REV. B
OUT
SS
OUT
A, V
DAC
OUT
B) voltage from the AD7569 DAC. V
Range Selection Input. This is used with the
Data Bit 6 to Data Bit 2.
Digital Ground.
Description
Analog Ground for the DAC(s). Separate
ground return paths are provided for the
DAC(s) and ADC to minimize crosstalk.
Output Voltage. V
V
from the AD7669. Four different output volt-
age ranges can be achieved (see Table I).
Negative Supply Voltage (–5 V for dual sup-
ply or 0 V for single supply). This pin is also
used with the RANGE pin to select the differ-
ent input/output ranges and changes the data
format from binary (V
ment (V
V
Table I. The range selected applies to both
the analog input voltage of the ADC and the
output voltage from the DAC(s).
Reset Input (Active Low). This is an asyn-
chronous system reset that clears the DAC
register(s) to all 0s and clears the INT line of
the ADC (i.e., makes the ADC ready for new
conversion). In unipolar operation, this input
sets the output voltage to 0 V; in bipolar
operation, it sets the output to negative full
scale.
Data Bit 7. Most Significant Bit (MSB).
Data Bit 1.
Data Bit 0. Least Significant Bit (LSB).
Write Input (Edge triggered). This is used in
conjunction with CS to write data into the
AD7569 DAC register. It is used in conjunc-
tion with CS and A/B to write data into the
selected DAC register of the AD7669. Data is
transferred on the rising edge of WR.
OUT
SS
input to select the different ranges as per
B are the buffered DAC output voltages
SS
= –5 V) (see Table I).
Range
0
1
0
1
OUT
SS
is the buffered output
= 0 V) to 2s comple-
V
0 V
0 V
–5 V
–5 V
SS
Table I. Input/Output Ranges
OUT
A and
Input/Output
Voltage Range
0 V to +1.25 V
0 V to +2.5 V
1.25 V
2.5 V
–7–
Pin
Mnemonic
CS
RD
ST
BUSY
INT
A/B (AD7669
Only)
CLK
AGND
V
V
IN
DD
ADC
DB0–DB7
Data Format
Binary
Binary
2s Complement
2s Complement
Description
Chip Select Input (Active Low). The device is
selected when this input is active.
READ Input (Active Low). This input must
be active to access data from the part. In the
Mode 2 interface, RD going low starts con-
version. It is used in conjunction with the CS
input (see Digital Interface Section).
Start Conversion (Edge triggered). This is
used when precise sampling is required. The
falling edge of ST starts conversion and drives
BUSY low. The ST signal is not gated with
CS.
BUSY Status Output (Active Low). When
this pin is active, the ADC is performing a
conversion. The input signal is held prior to
the falling edge of BUSY (see Digital Inter-
face Section).
INTERRUPT Output (Active Low). INT go-
ing low indicates that the conversion is com-
plete. INT goes high on the rising edge of CS
or RD and is also set high by a low pulse on
RESET (see Digital Interface Section).
DAC Select Input. This input selects which
DAC register data is written to under control
of CS and WR. With this input low, data is
written to the DACA register; with this input
high, data is written to the DACB register.
A TTL compatible clock signal may be used
to determine the ADC conversion time. Inter-
nal clock operation is achieved by connecting
a resistor and capacitor to ground.
Analog Ground for the ADC.
Analog Input. Various input ranges can be se-
lected (see Table I).
Positive Supply Voltage (+5 V).
AD7569/AD7669