MAX13037ATX+T Maxim Integrated Products, MAX13037ATX+T Datasheet
MAX13037ATX+T
Specifications of MAX13037ATX+T
Related parts for MAX13037ATX+T
MAX13037ATX+T Summary of contents
Page 1
... Other Control ECUs SPI is a trademark of Motorola, Inc. Pin Configuration and Typical Application Circuit at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. Automotive Contact Monitor and ...
Page 2
Automotive Contact Monitor and Level Shifters with LDO Regulator ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND, unless otherwise noted.) V ........................................................................-0.3V to +6.0V LO BAT.........................................................................-0.3V to +42V IN_ , BATREF...........................................................-45V to +45V IN_ to BAT ...............................................................-45V to +45V SD, ...
Page 3
Level Shifters with LDO Regulator ELECTRICAL CHARACTERISTICS (continued) (BAT = +6V to +26V -40°C to +125°C, unless otherwise noted. Typical values are at BAT = +14V PARAMETER SYMBOL SWITCH INPUTS (IN0–IN7) Input Voltage Threshold Center V ...
Page 4
Automotive Contact Monitor and Level Shifters with LDO Regulator ELECTRICAL CHARACTERISTICS (continued) (BAT = +6V to +26V -40°C to +125°C, unless otherwise noted. Typical values are at BAT = +14V PARAMETER SYMBOL LINEAR REGULATOR Output Voltage ...
Page 5
Level Shifters with LDO Regulator TIMING CHARACTERISTICS (continued) (BAT = +6V to +26V -40°C to +125°C, unless otherwise noted. Typical values are at BAT = +14V PARAMETER SYMBOL SDI to Falling Edge of CLK t Required ...
Page 6
Automotive Contact Monitor and Level Shifters with LDO Regulator CS t LEAD CLK t SI(SU) SDI MSB IN t SO(EN) SDO MSB OUT Figure 1. SPI Timing Characteristics MAX13037/ MAX13038 CS SDO Figure 2. SDO Enable/Disable Test Circuit and Timing ...
Page 7
Level Shifters with LDO Regulator (BAT = +14V 61kΩ, R BAT WET WETTING CURRENT vs. V BAT GND-CONNECTED SWITCH 0 -10 BAT-CONNECTED SWITCH -20 - ...
Page 8
Automotive Contact Monitor and Level Shifters with LDO Regulator (BAT = +14V 61kΩ, R BAT WET SWITCHING THRESHOLD vs. TEMPERATURE 10 ADJUSTABLE HYSTERESIS OFF RISING IN_ 7 V FALLING IN_ 6 ...
Page 9
61kΩ, R BAT WET V TRANSIENT LOAD REGULATION 50mA/div V LO (AC-COUPLED) 50mV/div 1ms/div PIN NAME 1, 15, 31 GND Ground Switch Input Channel 0. Connect IN0 to ...
Page 10
Automotive Contact Monitor and Level Shifters with LDO Regulator PIN NAME Shutdown Input. Drive SD low to place the MAX13037/MAX13038 into shutdown mode and disable SD 19 the linear regulator. Drive SD high for normal operation compatible with ...
Page 11
Level Shifters with LDO Regulator SD MAX13037 MAX13038 REGON WAKE-UP LOGIC REGOFF BATREF IN0 IN1 IN2 WETTING IN3 CURRENT CONTROL IN4 IN5 IN6 IN7 WET Detailed Description The MAX13037/MAX13038 automotive contact monitor and level shifters monitor and debounce eight remote ...
Page 12
Automotive Contact Monitor and Level Shifters with LDO Regulator BAT is the main power-supply input. Bypass BAT to ground with a 0.1µF ceramic capacitor placed as close as possible to BAT. In addition, bypass BAT with a 10µF or greater ...
Page 13
Level Shifters with LDO Regulator Mechanical Switch Inputs (IN0–IN7) IN0–IN7 are the inputs for remote mechanical switches. The status of each switch input is indicated by the SW0 through SW7 bits in the status register, and each switch input can ...
Page 14
Automotive Contact Monitor and Level Shifters with LDO Regulator Wetting Current (WET) The MAX13037/MAX13038 feature adjustable wetting current to any closed switch to clean switch contacts that are exposed to adverse conditions. The wetting current is set by connecting a ...
Page 15
Level Shifters with LDO Regulator STATUS REGISTER IS COPIED TO SHIFT REGISTER CS CLK SDI WTOFF SC2 SC1 SC0 SDO SW7 SW6 SW5 * = UNUSED. Figure 7. SPI Read/Write Example Serial Peripheral Interface ( CS ...
Page 16
Automotive Contact Monitor and Level Shifters with LDO Regulator Notes: Bit 15: Wetting Current Mode (WTOFF) Set the WTOFF bit to configure the wetting currents as continuous on closed switches. Clear the WTOFF bit to configure the wetting current as ...
Page 17
Level Shifters with LDO Regulator Table 5. Switch Configuration Controlled by M1 and M0 IN7 AND IN6 SWITCH M1 M0 CONFIGURATION 0 0 Ground 0 1 Ground 1 0 Battery 1 1 Battery IN1 (see Table 4). The DO0 and ...
Page 18
Automotive Contact Monitor and Level Shifters with LDO Regulator at which point the command register is restored to its power-up default (0x00) and the MAX13037/ MAX13038 enter scan mode. Note that SD is compati- ble with both logic and BAT ...
Page 19
Automotive Contact Monitor and Level Shifters with LDO Regulator TOP VIEW DO0 28 *EP THRESH 29 WDI 30 GND 31 32 BATREF MAX13037/MAX13038 N. BAT + BAT 36 (6mm x 6mm) *CONNECT EXPOSED PADDLE TO ...
Page 20
Automotive Contact Monitor and Level Shifters with LDO Regulator 0.01μF DO0 DO1 4700pF TDEB MAX13036 WET 90kΩ HYST 30kΩ GND Chip Information PROCESS: BiCMOS 20 ______________________________________________________________________________________ Typical Operating Circuit ECU CONNECTOR 0.01μF BATREF BATREF BAT BAT 47μF 0.1μF 0.1μF SDI ...
Page 21
Level Shifters with LDO Regulator (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ Automotive Contact Monitor and Package Information 21 ...
Page 22
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 22 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2007 Maxim Integrated Products Package Information (continued registered trademark of Maxim Integrated Products, Inc ...