USB3500-ABZJ SMSC, USB3500-ABZJ Datasheet - Page 35

• Manufacturer Part Number: USB3500-ABZJ
• Description: IC USB HOST/OTG PHY W/UTMI 56QFN
• Manufacturer: SMSC

Specifications of USB3500-ABZJ

• Applications: *
• Interface: *
• Voltage - Supply: *
• Package / Case: *
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 638-1035

Hi-Speed USB Host, Device or OTG PHY With UTMI+ Interface
Datasheet
SMSC USB3500
7.7
7.8
HS Detection Handshake
HS Detection Handshake – FS Downstream Facing Port
The downstream facing port asserting an SE0 state on the bus initiates the HS Detection Handshake.
There are three ways in which a device may enter the HS Handshake Detection process:
1. If the device is suspended and it detects an SE0 state on the bus it may immediately enter the HS
2. If the device is in FS mode and an SE0 state is detected for more than 2.5µs. it may enter the HS
3. If the device is in HS mode and an SE0 state is detected for more than 3.0ms. it may enter the
In each case, the assertion of the SE0 state on the bus initiates the reset. The minimum reset interval
is 10ms. Depending on the previous mode that the bus was in, the delay between the initial assertion
of the SE0 state and entering the HS Handshake detection can be from 0 to 4ms.
This transceiver design pushes as much of the responsibility for timing events on to the Link as
possible, and the Link requires a stable CLKOUT signal to perform accurate timing. In case 2 and 3
above, CLKOUT has been running and is stable, however in case 1 the USB3500 is reset from a
suspend state, and the internal oscillator and clocks of the transceiver are assumed to be powered
down. A device has up to 6ms after the release of SUSPENDN to assert a minimum of a 1ms Chirp K.
Upon entering the HS Detection process (T0), XCVRSELECT and TERMSELECT are in FS mode.
The DP pull-up is asserted and the HS terminations are disabled. The Link then sets OPMODE to
Disable Bit Stuffing and NRZI encoding, XCVRSELECT to HS mode, and begins the transmission of
all 0's data, which asserts a HS K (chirp) on the bus (T1). The device chirp must last at least 1.0ms,
and must end no later than 7.0ms after HS Reset T0. At time T1 the device begins listening for a chirp
sequence from the host port.
If the downstream facing port is not HS capable, then the HS K asserted by the device is ignored and
the alternating sequence of HS Chirp K’s and J’s is not generated. If no chirps are detected (T4) by
the device, it will enter FS mode by returning XCVRSELECT to FS mode.
handshake detection process.
handshake detection process.
HS handshake detection process. In HS mode, a device must first determine whether the SE0 state
is signaling a suspend or a reset condition. To do this the device reverts to FS mode by placing
XCVRSELECT and TERMSELECT into FS mode. The device must not wait more than 3.125ms
before the reversion to FS mode. After reverting to FS mode, no less than 100µs and no more
than 875µs later the Link must check the LINESTATE signals. If a J state is detected the device
will enter a suspend state. If an SE0 state is detected, then the device will enter the HS Handshake
detection process.
DATASHEET
35
Revision 1.0 (06-05-08)