LMH0040SQ/NOPB National Semiconductor, LMH0040SQ/NOPB Datasheet - Page 13
![IC SERIALIZER/CABLE DVR 48-LLP](/photos/6/51/65163/pkg_sqa48a_sml.jpg)
LMH0040SQ/NOPB
Manufacturer Part Number
LMH0040SQ/NOPB
Description
IC SERIALIZER/CABLE DVR 48-LLP
Manufacturer
National Semiconductor
Datasheet
1.LMH0070SQENOPB.pdf
(26 pages)
Specifications of LMH0040SQ/NOPB
Applications
Displays
Interface
LVDS
Voltage - Supply
3.135 V ~ 3.465 V
Package / Case
48-LLP
Mounting Type
Surface Mount
Number Of Elements
1
Number Of Receivers
5
Number Of Drivers
1
Input Type
CMOS
Operating Supply Voltage (typ)
3.3V
Differential Input High Threshold Voltage
100mV
Diff. Input Low Threshold Volt
-100mV
Output Type
Serializer
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
48
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
LMH0040SQ
Application Information
PCB RECOMMENDATIONS
The SMPTE Serial specifications have very stringent require-
ments for output return loss on drivers. The output return loss
will be degraded by non-idealities in the connection between
the SER (all variants with the exception of the LMH0050) and
the output connector. All efforts should be taken to minimize
the trace lengths for this area, and to assure that the charac-
teristic impedance of this trace is 75Ω.
It is recommended that the PCB traces between the host FP-
GA and the SER be no longer than 10 inches (25cm) and that
the traces be routed as differential pairs, with very tight match-
ing of line lengths and coupling within a pair, as well as equal
length traces for each of the six pairs. For additional informa-
tion on layout and soldering of the LLP package, please refer
to the applications note 'AN 1187'
PCB Design do’s and don’ts:
•
•
•
•
•
•
•
•
•
•
TYPICAL SMPTE APPLICATIONS CIRCUIT
A typical application circuit for the LMH0340 is shown in
ure
LMH0070 Serializers in lower data rate SMPTE applications.
The TX interface between the host FPGA and the SER is
composed of a 5-bit LVDS Data bus and its LVDS clock. This
DO Whenever possible dedicate an entire layer to each
power supply – this will reduce the inductance in the
supply plane.
DO use surface mount components whenever possible
DO place bypass capacitors close to each power pin
DON’T create ground loops – pay attention to the cutouts
that are made in your power and ground planes to make
sure that there are not opportunities for loops.
DON’T allow discontinuities in the ground planes – return
currents will follow the path of least resistance – for high
frequency signals this will be the path of least inductance.
DO place the SER outputs as close as possible to the edge
of the PCB where it will connect to the outside world.
DO make sure to match the trace lengths of all differential
traces, both between the sides of an individual pair, and
from pair to pair.
DO remember that VIAs have significant inductance –
when using a via to connect to a power supply or ground
layer, two in parallel are better than one.
DO connect the slug on the bottom of the package to a
solid Ground connection. This contact is used for the major
GND connection to the device as well as serving as a
thermal via to keep the die at a low operating temperature.
There is an application note available which discusses
layout suggestions for the SER in greater detail.
13. Alternately this could also employ the LMH0040 or
Fig-
13
is a point-to-point interface and the SER includes on-chip 100
terminations. Pairs should be of equal length to minimize any
skew impact. The LVDS clock (TXCLK) uses both edges to
transfer the data.
An SMBus is also connected from the host FPGA to the SER.
If the SMBus is shared, a chip select signal is used to select
the device being addressed. The SCK and SDA signals re-
quire a pull up resistor. The SMB_CS is driven by a GPO
signal from the FPGA. Depending on the FPGA I/O it may also
require a pull up unless it is a push / pull output.
Depending upon the application, several other GPIO signals
maybe used. This includes the DVB_ASI and RESET input
signals. If these pins are not used, then must be tied off to the
desired state. The LOCK signal maybe used to monitor the
SER. If it is unused, leave the pin as a NC (or route to a test
point).
The SER includes a SMPTE compliant cable driver. While this
is a differential driver, it is commonly used single-endedly to
drive 75 Ω coax cables. External 75 Ω pull up resistors are
used to the 2.5V rail. The active output(s) also includes a
matching network to meet the required Output Return Loss
SMPTE specification. While application specific, in general a
series 75 Ω resistor shunted by a 6.8 nH inductor will provide
a starting value to design with. The signal is then AC coupled
to the cable with a 4.7 µF capacitor. If the complementary
output is not used, simply terminate it after its AC coupling
capacitor to ground. This output (even though its inverting)
may still be used for a loop back or 1:2 function due to the
nature of the NRZI coding that the SMPTE standards require.
The output voltage amplitude of the cable driver is set by the
R
sistor is connected between this pin and ground to set the
swing to 800mV.
The PLL loop filter is external for the SER. A capacitor is con-
nected in series to a resistor between the LF_CP and LF_REF
pins. Typical values are 500 Ω and 0.1 µF.
There are several configuration pins that requiring setting to
the proper level. The RSVD_H pins should be pulled High to
the 3.3V rail with a 5 kΩ resistor. Depending upon the appli-
cation the DVB_ASI pin may be tied off or driven.
There are three supply connections (see By Pass discussion
and also Pin Descriptions for recommendations). The two
main supplies are the 3.3V rail and the 2.5V rail. There is also
a 3.3V connection for the PLL circuitry.
There are multiple Ground connections for the device. The
main ground connection for the SER is through the large cen-
ter DAP pad. This must be connected to ground for proper
device operation. In addition, multiple other inputs are re-
quired to be connected to ground as show in the figure and
listed in the Pin Description table.
SET
resistor. For single-ended applications, an 8.06 kΩ re-
www.national.com