NCP382LMN10AATXG ON Semiconductor, NCP382LMN10AATXG Datasheet
NCP382LMN10AATXG
Specifications of NCP382LMN10AATXG
Related parts for NCP382LMN10AATXG
NCP382LMN10AATXG Summary of contents
Page 1
NCP382 Fixed Current-Limiting Power-Distribution Switches The NCP382 is a single input dual outputs high side power−distribution switch designed for applications where heavy capacitive loads and short−circuits are likely to be encountered, incorporating two 80 mW, P−channel MOSFETs in a single ...
Page 2
USB INPUT 5V FLAG1 EN1 FLAG2 EN2 GND DFN8 3 EN1 4 EN2 PIN FUNCTION DESCRIPTION Pin Name Type EN1 I Enable 1 input, logic low/high (i. EN) turns on power switch. EN2 I Enable ...
Page 3
MAXIMUM RATINGS Rating From IN to OUT1, From IN to OUT2 Supply Voltage (Note 1) IN, OUT1,OUT2, EN1, EN2, FLAG1, FLAG2 (Note 1) FLAG1, FLAG2 sink current ESD Withstand Voltage (IEC 61000−4−2) (output only, when bypassed with 1.0 mF capacitor ...
Page 4
OPERATING CONDITIONS Symbol Parameter V Operational Power Supply IN V Enable Voltage ENX T Ambient Temperature Range A I FLAG sink current SINK C Decoupling input capacitor IN C Decoupling output capacitor OUTX R Thermal Resistance Junction−to−Air qJA T Junction ...
Page 5
ELECTRICAL CHARACTERISTICS 2 5.5 V (Unless otherwise noted). Typical values are referenced to T Symbol Parameter POWER SWITCH R Static drain−source on−state resistance DS(on) T Output rise time R T Output fall time F ENABLE INPUT ENx OR ...
Page 6
VIN 0 50% ENx V ENx T ON 90% V OUTx IN OUT1 NCP382 C OUT2 GND C Figure 3. Test Configuration V OUTx T OFF 10% Figure 4. Voltage Waveform http://onsemi.com 6 R LOAD LOAD R LOAD ...
Page 7
EN1 EN block Current Limiter GND Oscilator V REF IN UVLO TSD Current Limiter EN2 EN block BLOCK DIAGRAM Control logic and timer Gate Driver Blocking control Blocking control Gate Driver Control logic and timer Figure 5. Block Diagram http://onsemi.com ...
Page 8
... NCP382 stays in on−phase/off−phase loop until the over current condition is removed or enable pin is toggled. Remark: other regulation mode can be available for different applications. Please contact our On Semiconductor representative for availability. FLAG Indicator The FLAG pin is an open−drain MOSFET asserted low during overcurrent or overtemperature conditions ...
Page 9
Enable Input Enable pin must be driven by a logic signal (CMOS or TTL compatible) or connected to the GND or VIN. A logic low on ENX or high on ENX turns−on the device. A logic high on ENX or ...
Page 10
... ORDERING INFORMATION Device Marking NCP382LMN05AATXG 382 L05 NCP382LMN10AATXG 382 L10 NCP382LMN15AATXG 382 L15 NCP382HMN05AATXG 382 H05 NCP382HMN10AATXG 382 H10 NCP382HMN15AATXG 382 H15 NCP382LD05AAR2G 382L05 NCP382LD10AAR2G 382L10 NCP382LD15AAR2G 382L15 NCP382HD05AAR2G 382H05 NCP382HD10AAR2G 382H10 NCP382HD15AAR2G 382H15 †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D ...
Page 11
... *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “ ...