DS90LV004TVS/NOPB National Semiconductor, DS90LV004TVS/NOPB Datasheet - Page 5

• Manufacturer Part Number: DS90LV004TVS/NOPB
• Description: IC REPEATER 4CH BUS LVDS 48-TQFP
• Manufacturer: National Semiconductor
• Type: Repeaterr

Specifications of DS90LV004TVS/NOPB

• Tx/rx Type: LVDS
• Delay Time: 3.2ns
• Capacitance - Input: 3.5pF
• Voltage - Supply: 3.15 V ~ 3.45 V
• Current - Supply: 140mA
• Mounting Type: Surface Mount
• Package / Case: 48-TQFP, 48-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *DS90LV004TVS; *DS90LV004TVS/NOPB; *DS90LV004TVSNOPB; DS90LV004TVS; DS90LV004TVSNOPB; DS90LV004TVSNOPB

LVDS OUTPUT DC SPECIFICATIONS (OUTn±)
V
ΔV
V
ΔV
I
C
SUPPLY CURRENT (Static)
I
I
SWITCHING CHARACTERISTICS—LVDS OUTPUTS
t
t
t
t
t
t
t
t
t
t
OS
CC
CCZ
LHT
HLT
PLHD
PHLD
SKD1
SKCC
SKP
JIT
ON
OFF
Symbol
OD
OS
OUT2
Note 4: Typical parameters are measured at V
Note 5: Differential output voltage V
Note 6: Output offset voltage V
Note 7: Jitter is not production tested, but guaranteed through characterization on a sample basis.
Note 8: Random Jitter, or RJ, is measured RMS with a histogram including 1500 histogram window hits. The input voltage = V
750MHz, t
Note 9: Deterministic Jitter, or DJ, is measured to a histogram mean with a sample size of 350 hits. The input voltage = V
t
Note 10: Total Jitter, or TJ, is measured peak to peak with a histogram including 3500 window hits. Stimulus and fixture Jitter has been subtracted. The input
voltage = V
Note 11: Not production tested. Guaranteed by a statistical analysis on a sample basis at the time of characterization.
r
OD
OS
= t
f
= 50ps (20% to 80%). The K28.5 pattern is repeating bit streams of (0011111010 1100000101).
r
Differential Output Voltage,
0% Pre-emphasis (Note 5)
Change in V
Complementary States
Offset Voltage (Note 6)
Change in V
Complementary States
Output Short Circuit Current
Output Capacitance
Supply Current
Supply Current - Power Down
Mode
Differential Low to High
Transition Time
Differential High to Low
Transition Time
Differential Low to High
Propagation Delay
Differential High to Low
Propagation Delay
Pulse Skew
Output Channel to Channel Skew Difference in propagation delay (t
Part to Part Skew
Jitter (0% Pre-emphasis)
(Note 7)
LVDS Output Enable Time
LVDS Output Disable Time
ID
= t
= 500mV, 2
f
= 50ps (20% to 80%).
Parameter
23
OD
OS
-1 PRBS pattern at 1.5 Gbps, t
between
between
OS
is defined as the average of the LVDS single-ended output voltages at logic high and logic low states.
OD
is defined as ABS(OUT+–OUT−). Differential input voltage V
DD
= 3.3V, T
R
OUT−
OUT+ or OUT− Short to GND
OUT+ or OUT− to GND when TRI-STATE
All inputs and outputs enabled and active,
terminated with differential load of 100Ω between
OUT+ and OUT-, 0% pre-emphasis
PWDN = L, 0% pre-emphasis
Use an alternating 1 and 0 pattern at 200 Mbps,
measure between 20% and 80% of V
11)
Use an alternating 1 and 0 pattern at 200 Mbps,
measure at 50% V
|t
among all output channels. (Note 11)
Common Edge, parts at same temp and V
11)
RJ - Alternating 1 and 0 at 750 MHz (Note 8)
DJ - K28.5 Pattern, 1.5 Gbps (Note 9)
TJ - PRBS 2
Time from PWDN to OUT± change from TRI-
STATE to active.
Time from PWDN to OUT± change from active to
TRI-STATE.
PLHD
L
= 100Ω external resistor between OUT+ and
r
= t
A
–t
= 25°C. They are for reference purposes, and are not production-tested.
f
PHLD
= 50ps (20% to 80%).
| (Note 11)
23
-1 Pattern, 1.5 Gbps (Note 10)
OD
Conditions
5
between input to output.
PLHD
OD
ID
or t
is defined as ABS(IN+–IN−).
. (Note
PHLD
CC
®
(Note
)
1.05
Min
250
−35
−35
ID
= 500mV, K28.5 pattern at 1.5 Gbps,
ID
(Note 4)
= 500mV, 50% duty cycle at
1.18
Typ
500
−60
117
210
210
5.5
2.7
2.0
2.0
1.1
25
50
43
35
1.475
Max
600
−90
140
300
300
125
300
3.2
3.2
1.1
1.5
35
35
80
62
85
12
6
www.national.com
psrms
Units
psp-p
psp-p
mV
mV
mV
mA
mA
mA
pF
ps
ps
ns
ns
ps
ps
ns
ns
ns
V