ADM1022ARQ-REEL7 ON Semiconductor, ADM1022ARQ-REEL7 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ADM1022ARQ-REEL7
Manufacturer Part Number
ADM1022ARQ-REEL7
Description
IC SENSOR TEMP/DET 3/5.5V 16QSOP
Manufacturer
ON Semiconductor
Type
Temperature Sensorr
Datasheet
1.ADM1022ARQ-REEL.pdf
(19 pages)
Specifications of ADM1022ARQ-REEL7
Rohs Status
RoHS non-compliant
Input Type
Logic
Output Type
Analog
Interface
Serial
Current - Supply
2.6mA
Mounting Type
Surface Mount
Package / Case
16-QSOP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADM1022ARQ-REEL7
Manufacturer:
AD
Quantity:
2 000
ADM1022
GENERAL PURPOSE LOGIC INPUT (GPI)
Pin 12 may be configured as an input for a second temperature
sensor input by setting Bit 7 of the Configuration Register, or it
may be used as a general purpose logic input by clearing Bit 7 of
the Configuration Register, which is its default condition. The
GPI input may be programmed to be active high or active low by
clearing or setting Bit 6 of the Configuration Register. The default
value is active high. Bit 4 of the Interrupt Status Register follows
the state (or inverted state) of GPI and will generate an interrupt
when it is set to one, like any other input to the Interrupt Status
Register. However, the GPI bit is not latched in the Status Register
and always reflects the current state (or inverted state) of the
GPI input. If it is one it will not be cleared by reading the
Status Register.
RESETS
The ADM1022 has a manual reset input, (Pin 2 – MR), a bidi-
rectional reset pin, (Pin 3 – RST1) and a reset output (Pin 7 –
RST2). These operate as follows:
Taking MR low forces a system reset and takes the RST2 output
low. It will remain low for t
MR input has a 20 kΩ pull-up resistor, and may be left uncon-
nected if not used. MR is typically used to generate a system
reset from a front-panel push-button.
The RST1 pin is a bidirectional I/O. It is asserted low as an out-
put if V
reset input to the ADM1022 in the same way as MR. At power-
up, RST2 will remain asserted for t
The RST2 output is asserted low under any of the following
conditions:
≤ the MR input is low, as previously described,
– RST1 is asserted low as an output or pulled low as an input,
≤ V
POWER-ON RESET
When the ADM1022 is powered up, it will initiate a power-on
reset sequence when the supply voltage V
power-on reset threshold, with registers being reset to their
power-on values. Normal operation will begin when the supply
voltage rises above the reset threshold. Registers whose power-
on values are not shown have power on conditions that are
indeterminate (this includes the Value and Limit Registers). In
most applications, usually the first action after power-on would
be to write limits into the Limit Registers.
Power-on reset clears or initializes the following registers (the ini-
tialized values are shown in Table IV):
– Configuration Register
– Interrupt Status Register
– Interrupt Status Mirror Register
– Interrupt Mask Register
– Test Register
– Analog Output Register
– Programmable Trip Point Registers
MON
CC
is below the reset threshold.
falls below the reset threshold. It can also operate as a
RP
after MR goes high again. The
RP
after RST1 goes high.
CC
rises above the
Operation of the reset outputs at power-up, and for a manual
reset input, is shown in Figure 18. It should be noted that the
resets will only be asserted once V
voltage there is insufficient gate drive voltage to turn on the out-
put FETs. If the device being reset and its pull-up resistor is
supplied from V
before being pulled low. If the device being reset and its pull-up
resistor use a separate supply voltage, the reset output will fol-
low that voltage until reset is asserted.
The ADM1022 can also be reset by taking RST1 low as an input.
The above-mentioned registers will be reset to their default
values and the ADC will remain inactive as long as RST1 is
below the reset threshold.
RST1 AS I/O
If RST1 is used as a reset input to the ADM1022 while also
being used as a system reset output, it will be necessary to sepa-
rate the two functions so that a reset from the system to the
ADM1022 does not also reset the system.
This can be achieved using the circuit of Figure 19. If ALT_RST
is high, then reset outputs from the ADM1022 can pass through
N2 to reset the system.
If, however, ALT_RST is low, the ADM1022 will be reset, but
SYS_RST will be held high by the high input from N1 to N2.
RST1
RST2
RST2
V
MR
CC
ALT_RST
ADM1022
–1V
CC
RST1
, the reset voltage will rise with V
t
MANUAL RESET (FOR EXAMPLE)
N1
t
RP
POWER-ON RESET
RST1
V
t
RP
CC
100k
CC
t
RP
rises above 1 V. Below this
N2
RST1
SYS_RST
CC
to 1 V