AD694BRZ Analog Devices Inc, AD694BRZ Datasheet - Page 5

• Manufacturer Part Number: AD694BRZ
• Description: IC TRANSMITTER 4-20MA 16-SOIC
• Manufacturer: Analog Devices Inc
• Type: Current Transmitterr

Specifications of AD694BRZ

• Input Type: Voltage
• Output Type: Voltage
• Current - Supply: 23mA
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Number Of Channels: 1
• Number Of Elements: 3
• Power Supply Requirement: Single
• Common Mode Rejection Ratio: 80dB
• Voltage Gain Db: 93.98dB
• Input Resistance: 5@24VMohm
• Input Offset Voltage: 0.5@24VmV
• Input Bias Current: 0.005@24V@-55C TO 12nA
• Single Supply Voltage (typ): 5/9/12/15/18/24/28V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Rejection Ratio: 80dB
• Rail/rail I/o Type: No
• Single Supply Voltage (min): 4.5V
• Single Supply Voltage (max): 36V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: SOIC W
• No. Of Amplifiers: 2
• Bandwidth: 300kHz
• Amplifier Output: Single Ended
• Cmrr: 90dB
• Slew Rate: 1.3V/µs
• Supply Voltage Range: 4.5V To 36V
• Supply Current: 1.5mA
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Interface: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

optional NPN pass transistor can be added to transfer most of
the power dissipation off-chip, to extend the temperature range
of operation.
The output stage is current-limited at approximately 38 mA to
protect the output from an overdrive at its inputs. The V/I will
allow linear operation to approximately 24 mA. The V/I con-
verter also has an open collector alarm (Pin 10) which warns of
open-circuit condition at the I
output to a voltage greater than V
4 mA OFFSET GENERATOR
This circuit converts a constant voltage from the voltage
reference to a constant current of approximately 200 µA. This
current is summed with the signal current at Pin 14 (BW
Adjust), to result in a constant 4 mA offset current at I
4 mA Adj (Pin 6) allows the offset current to be adjusted to any
current in the range of 2 mA to 4.8 mA. Pin 9 (4 mA On/Off)
can shut off the offset current completely if it is lifted to 3.0 V or
more, allowing 0 to 20 mA operation of the AD694. In normal
4–20 mA operation, Pin 9 is connected to ground.
VOLTAGE REFERENCE
A 2 V or 10 V voltage reference is available for user applications,
selectable by pin-strapping. The 10 V option is available for
supply voltages greater than 12.5 V, the 2 V output is available
over the whole 4.5 V to 36 V power supply range. The reference
can source up to 5 mA for user applications. A boost transistor
can be added to increase the current drive capability of the 2 V
mode.
APPLYING THE AD694
The AD694 can easily be connected for either dual or single
supply operation, to operate from supplies as low as 4.5 V and
as high as 36 V. The following sections describe the different
connection configurations, as well as adjustment methods.
Table I shows possible connection options.
REV. B
Figure 2. Minimal Connections for 0 V to 10 V Single-Ended Input, 4–20 mA Output, 10 V Reference Output
OUT
S
pin or of attempts to drive the
– 2 V.
OUT
. The
–5–
I
Range
0–2 V
0–10 V
0–2.5 V
0–12.5 V 0–20 mA 2 V
0–2 V
0–10 V
0–2.5 V
0–12.5 V 0–20 mA 10 V
BASIC CONNECTIONS: 12.5 V SINGLE-SUPPLY
OPERATION WITH 10 V FS
Figure 2 shows the minimal connections required for basic
operation with a 12.5 V power supply, 10 V input span,
4–20 mA output span, and a 10 V voltage reference. The buffer
amplifier is connected as a voltage follower to drive the V/I
converter by connecting FB (Pin 1) to –Sig (Pin 2). 4 mA On/
Off (Pin 9) is tied to ground (Pin 5) to enable the 4 mA offset
current. The AD694 can drive a maximum load R
/20 mA, thus the maximum load with a 12.5 V supply is 525 Ω.
SELECTING A 2 V FULL-SCALE INPUT
The 2 V full-scale option is selected by shorting Pin 4 (2 V FS)
to Pin 5 (Common). The connection should be as short as pos-
sible; any parasitic resistance will affect the precalibrated span
accuracy.
SELECTING THE 2 V VOLTAGE REFERENCE
The voltage reference is set to a 2 V output by shorting Pin 7 to
Pin 8 (10 V Force to 2 V Sense). If desired, the 2 V reference
can be set up for remote force and sense connection. Keep in
mind that the 2 V Sense line carries a constant current of 100 µA
that could cause an offset error over long wire runs. The 2 V
reference option can be used with all supply voltages greater
than 4.5 V.
nput
Table I. Precalibrated Ranges for the AD694
Output
Range
4–20 mA 2 V
4–20 mA 2 V
0–20 mA 2 V
4–20 mA 10 V
4–20 mA 10 V
0–20 mA 10 V
Voltage
Reference V
Min
4.5 V
12.5 V
5.0 V
15.0 V
12.5 V
12.5 V
12.5 V
15.0 V
S
Pin 9 Pin 4 Pin 8
Pin 5
Pin 5
≥3 V
≥3 V
Pin 5
Pin 5
≥3 V
≥3 V
AD694
L
Pin 5
Pin 5
Open
Pin 5
Open
Pin 5
Open
Open
= [V
S
– 2 V]
Pin 7
Pin 7
Pin 7
Pin 7
Open
Open
Open
Open