SI3008-B-FS Silicon Laboratories Inc, SI3008-B-FS Datasheet - Page 20

• Manufacturer Part Number: SI3008-B-FS
• Description: IC ISOMODEM FCC LINE-SIDE 8SOIC
• Manufacturer: Silicon Laboratories Inc

Specifications of SI3008-B-FS

• Data Format: V.22, V23, V.32, V.34, V.90, Bell 103, Bell 212A
• Baud Rates: 56k
• Interface: Parallel
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Product: Modem Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Si2401/Si3008
5. AT Command Set
The controller provides several vital functions including
AT command parsing, DAA control, connect sequence
control, DCE protocol control, intrusion detection,
parallel phone off-hook detection, escape control, caller
ID control and formatting, ring detect, DTMF control, call
progress monitoring, and HDLC framing. The controller
also writes to the control registers that configure the
modem. Virtually all interaction between the host and
the modem is done via the controller. The controller
uses AT (ATtention) commands and S-Registers to
configure and control the modem.
The modem has two modes of operation: command
mode and data mode. The Si2401 is asynchronous in
both command mode and data mode. The modem is in
command mode at powerup, after a reset, before a
connection is made, after a connection is dropped, and
during a connection after successfully “Escaping” from
the data mode back to the command mode using one of
the methods previously described. The following section
describes the AT command set available in command
mode.
The Si2401 supports a subset of the typical modem AT
command set since it is intended for use with a
dedicated microcontroller instead of general terminal
applications. AT commands begin with the letters AT
and are followed directly (no space) by the command.
These commands are also case-sensitive. All AT
commands must be entered in upper case including AT
except w##, r#, m#, q#, and z (wakeup-on-ring).
AT commands can be divided into two groups: control
commands and configuration commands. Control
commands, such as ATD, cause the modem to perform
an action (going off-hook and dialing). The value of this
type of command is changed at a particular time to
perform
ATDT1234<CR> command causes the modem to go off
hook and dial the number, 1234, via DTMF. This action
exists only during a connection attempt. No enduring
change in the modem configuration exists after the
connection or connection attempt has ended.
Configuration
characteristics until they are modified or reversed by a
subsequent configuration command or the modem is
reset. Modem configuration status can be determined
with the use of “ATSR?<CR>” Where R is the two-
character hexadecimal address of an S-register.
A command line is defined as a string of characters
starting with AT and ending with an end-of-line
character, <CR> (13 decimal). Command lines may
contain several commands one after the other. If there
20
a
particular
commands
action.
For
change
example,
modem
the
Rev. 1.1
are no characters between AT and <CR>, the modem
responds with “O” after the carriage return.
5.1. Command Line Execution
The characters in a command line are executed one-at-
a-time. Unexpected command characters are ignored,
but unexpected data characters may be interpreted
incorrectly.
After the modem has executed a command line, the
result code corresponding to the last command
executed is returned to the terminal or host. In addition
to the “ATH” and “ATZ” commands, the commands that
warrant a response (e.g., “ATSR?” or “ATI”) must be the
last in the string and followed by a <CR>. All other
commands may be concatenated on a single line. To
echo command line characters, set the Si2401 to Echo
mode using the E1 command.
All numeric arguments, including the address and value
of an S-register, are in hexidecimal format, and two
digits must always be entered.
5.2. <CR> End-Of-Line Character
This character is typed to end a command line. The
value of the <CR> character is 13 in decimal, the ASCII
carriage return character. When the <CR> character is
entered, the modem executes the commands in the
command line.
Note: Commands that do not require a response are exe-
Command
DP#
DT#
w##
RO
Table 12. AT Command Set Summary
m#
H0
H1
cuted immediately and do not need a <CR>.
M
r#
A
E
O
S
:I
I
Answer line immediately with modem
Tone dial number
Pulse dial number
Local echo on/off
Go on-hook (hang up modem)
Go off-hook
Chip revision
Interrupt read and clear
Speaker control options
Return online
V.23 reverse
Read/write S-Registers
Write S-Register in binary
Read S-Register in binary
Monitor S-Register in binary
Function