MAX7312ATG+T Maxim Integrated Products, MAX7312ATG+T Datasheet - Page 10
![IC I/O EXPANDER I2C 16B 24TQFN](/photos/6/50/65029/24-tqfn_21-0201a_sml.jpg)
MAX7312ATG+T
Manufacturer Part Number
MAX7312ATG+T
Description
IC I/O EXPANDER I2C 16B 24TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX7312ATG.pdf
(16 pages)
Specifications of MAX7312ATG+T
Interface
I²C, SMBus
Number Of I /o
16
Interrupt Output
Yes
Frequency - Clock
400kHz
Voltage - Supply
2 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
24-TQFN Exposed Pad
Includes
POR
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data is clocked into a register on the falling edge of the
acknowledge clock pulse. After reading the first byte,
additional bytes may be read and reflect the content in
the other register in the pair. For example, if input port 1
is read, the next byte read is input port 2. An unlimited
number of data bytes can be read in one read trans-
mission, but the final byte received must not be
acknowledged by the bus master.
The open-drain interrupt output, INT, activates when
one of the port pins changes states and only when the
pin is configured as an input. The interrupt deactivates
when the input returns to its previous state or the input
register is read (Figure 9). A pin configured as an out-
put does not cause an interrupt. Each 8-bit port register
is read independently; therefore, an interrupt caused
by port 1 is not cleared by a read of port 2’s register.
Changing an I/O from an output to an input may cause
a false interrupt to occur if the state of that I/O does not
match the content of the input port register.
2-Wire-Interfaced 16-Bit I/O Port Expander
with Interrupt and Hot-Insertion Protection
Figure 10. Simplified Schematic of I/Os
10
______________________________________________________________________________________
CONFIGURATION
SHIFT REGISTER
SHIFT REGISTER
WRITE PULSE
DATA FROM
DATA FROM
WRITE POLARITY
SHIFT REGISTER
PULSE
WRITE
READ PULSE
DATA FROM
POWER-ON
PULSE
RESET
CONFIGURATION
REGISTER
D
SET
CLR
Q
Q
OUTPUT PORT
REGISTER
D
SET
CLR
Interrupt ( INT )
Q
Q
POLARITY INVERSION
INPUT PORT
REGISTER
REGISTER
D
D
CLR
CLR
SET
SET
Q
Q
Q
Q
When an I/O is configured as an input, FETs Q1 and Q2
are off (Figure 10), creating a high-impedance input. All
inputs are overvoltage protected to 5.5V, independent
of supply voltage. When a port is configured as an out-
put, either Q1 or Q2 is on, depending on the state of the
output port register. When V
power-on reset sets all registers to their respective
defaults (Table 1).
The input port registers (Table 2) are read-only ports.
They reflect the incoming logic levels of the pins,
regardless of whether the pin is defined as an input or
an output by the respective configuration register. A
read of the input port 1 register latches the current
value of I/O0–I/O7. A read of the input port 2 register
latches the current value of I/O8–I/O15. Writes to the
input port registers are ignored.
Q1
Q2
POLARITY
REGISTER
DATA
+
powers up, an internal
Input/Output Port
Input Port Registers
OUTPUT PORT
REGISTER DATA
V
I/O PIN
V
INPUT PORT
REGISTER DATA
TO INT
DD
SS