MCP23018-E/SP Microchip Technology, MCP23018-E/SP Datasheet - Page 23

• Manufacturer Part Number: MCP23018-E/SP
• Description: IC I/O EXPANDER I2C 16B 28SDIP
• Manufacturer: Microchip Technology

Specifications of MCP23018-E/SP

• Package / Case: 28-DIP (0.300", 7.62mm)
• Interface: I²C
• Number Of I /o: 16
• Interrupt Output: Yes
• Frequency - Clock: 3.4MHz
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Logic Family: MCP23018
• Propagation Delay Time: 50 ns
• Operating Supply Voltage: 1.8 V to 5.5 V
• Power Dissipation: 700 mW
• Operating Temperature Range: - 40 C to + 125 C
• Input Voltage: 1.8 V to 5.5 V
• Logic Type: I/O Expander
• Maximum Clock Frequency: 10 MHz
• Maximum Operating Frequency: 3.4 MHz
• Mounting Style: Through Hole
• Output Current: 25 mA
• Output Voltage: 1.8 V to 4.5 V
• Chip Configuration: 16 Bit
• Bus Frequency: 3.4MHz
• Ic Interface Type: I2C
• No. Of I/o's: 16
• Supply Voltage Range: 1.8V To 5.5V
• Digital Ic Case Style: DIP
• No. Of Pins: 28
• Filter Terminals: DIP
• Rohs Compliant: Yes
• Delay Time: 50ns
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

1.6.6
The IOCON register contains several bits for
configuring the device:
The BANK bit changes how the registers are mapped
(see
• If BANK = 1, the registers associated with each
• If BANK = 0, the A/B registers are paired. For
It is important to take care when changing the BANK bit
as the address mapping changes after the byte is
clocked into the device. The address pointer may point
to an invalid location after the bit is modified.
For example, if the device is configured to automati-
cally increment its internal address pointer the following
scenario would occur:
• BANK = 0
• Write 80h to 0Ah (IOCON) to set the BANK bit
• After the write completes the internal address now
to this register when changing the BANK bit.
© 2008 Microchip Technology Inc.
For this reason, it is advised to only perform byte writes
port are segregated. Registers associated with
PORTA are are mapped from address 00h - 0Ah
and registers associated with PORTB are
mapped from Address 10h - 1Ah
example, IODIRA is mapped to address 00h and
IODIRB is mapped to the next address (address
01h). The mapping for all registers is from 00h -
points to 0Bh which is an invalid address when
the BANK bit is set
15h
Table 1-4
CONFIGURATION REGISTER
and
Table 1-5
for more details).
MCP23018/MCP23S18
The MIRROR bit controls how the INTA and INTB pins
function with respect to each other.
• When MIRROR = 1, the INTn pins are functionally
• When MIRROR = 0, the INT pins are separated.
The Sequential Operation (SEQOP) controls the
incrementing function of the address pointer. If the
address pointer is disabled, the address pointer does
not automatically increment after each byte is clocked
during a serial transfer. This feature is useful when it is
desired to continuously poll (read) or modify (write) a
register.
The Open-Drain (ODR) control bit enables/disables the
INT pin for open-drain configuration.
The Interrupt Polarity (INTPOL) sets the polarity of the
INT pin. This bit is functional only when the ODR bit is
cleared, configuring the INT pin as active push-pull.
The Interrupt Clearing Control (INTCC) configures how
interrupts are cleared. When set (INTCC = 1), the
interrupt is cleared when the INTCAP register is read.
When cleared (INTCC = 0), the interrupt is cleared
when the GPIO register is read.
The interrupt can only be cleared when the interrupt
condition is inactive. Refer to Section 1.7.5 “Clearing
Interrupts” for details.
Note:
OR’ed so that an interrupt on either port will cause
both pins to activate
Interrupt conditions on a port will cause its respec-
tive INT pin to activate
The INTB pin is not bonded out on the
MCP23S18 (SPI) device in the 24-lead
QFN package. The MIRROR bit must be
configured to a “1” in order for interrupts to
be detected on PORTB.
DS22103A-page 23