MCP23S17-E/SS Microchip Technology, MCP23S17-E/SS Datasheet - Page 18

• Manufacturer Part Number: MCP23S17-E/SS
• Description: IC I/O EXPANDER SPI 16B 28SSOP
• Manufacturer: Microchip Technology

Specifications of MCP23S17-E/SS

• Package / Case: 28-SSOP
• Interface: SPI
• Number Of I /o: 16
• Interrupt Output: Yes
• Frequency - Clock: 10MHz
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Logic Family: MCP23S17
• Propagation Delay Time: 50 ns
• Operating Supply Voltage: 1.8 V to 5.5 V
• Power Dissipation: 700 mW
• Operating Temperature Range: - 40 C to + 125 C
• Input Voltage: 1.8 V to 5.5 V
• Logic Type: I/O Expander
• Maximum Clock Frequency: 10 MHz
• Maximum Operating Frequency: 1.7 MHz
• Mounting Style: SMD/SMT
• Output Current: 25 mA
• Output Voltage: 1.8 V to 4.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP23X17EV - BOARD EVAL FOR MCP23X17GPIODM-KPLCD - BOARD DEMO LCD GPIO EXP KEYPAD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP23017/MCP23S17
REGISTER 1-6:
DS21952B-page 18
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W-0
BANK
BANK: Controls how the registers are addressed
1 = The registers associated with each port are separated into different banks
0 = The registers are in the same bank (addresses are sequential)
MIRROR: INT Pins Mirror bit
1 = The INT pins are internally connected
0 = The INT pins are not connected. INTA is associated with PortA and INTB is associated with PortB
SEQOP: Sequential Operation mode bit.
1 = Sequential operation disabled, address pointer does not increment.
0 = Sequential operation enabled, address pointer increments.
DISSLW: Slew Rate control bit for SDA output.
1 = Slew rate disabled.
0 = Slew rate enabled.
HAEN: Hardware Address Enable bit (MCP23S17 only).
Address pins are always enabled on MCP23017.
1 = Enables the MCP23S17 address pins.
0 = Disables the MCP23S17 address pins.
ODR: This bit configures the INT pin as an open-drain output.
1 = Open-drain output (overrides the INTPOL bit).
0 = Active driver output (INTPOL bit sets the polarity).
INTPOL: This bit sets the polarity of the INT output pin.
1 = Active-high.
0 = Active-low.
Unimplemented: Read as ‘0’.
MIRROR
R/W-0
IOCON – I/O EXPANDER CONFIGURATION REGISTER (ADDR 0x05)
W = Writable bit
‘1’ = Bit is set
SEQOP
R/W-0
DISSLW
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
HAEN
R/W-0
ODR
© 2007 Microchip Technology Inc.
x = Bit is unknown
INTPOL
R/W-0
U-0
—
bit 0