73S1210F-44M/F/PC Maxim Integrated Products, 73S1210F-44M/F/PC Datasheet - Page 65
73S1210F-44M/F/PC
Manufacturer Part Number
73S1210F-44M/F/PC
Description
Microcontrollers (MCU)
Manufacturer
Maxim Integrated Products
Datasheet
1.73S1210F-44MFPC.pdf
(126 pages)
Specifications of 73S1210F-44M/F/PC
Lead Free Status / Rohs Status
Details
- Current page: 65 of 126
- Download datasheet (2Mb)
DS_1210F_001
Keypad Scan Time Register (KSCAN): 0xD3 0x00
This register contains the values of scanning time and debouncing time.
Keypad Control/Status Register (KSTAT): 0xD4 0x00
This register is used to control the hardware keypad scanning and detection capabilities, as well as the
keypad interrupt control and status.
Rev. 1.4
KSCAN.7
KSCAN.6
KSCAN.5
KSCAN.4
KSCAN.3
KSCAN.2
KSCAN.1
KSCAN.0
KSTAT.7
KSTAT.6
KSTAT.5
KSTAT.4
KSTAT.3
KSTAT.2
KSTAT.1
KSTAT.0
MSB
DBTIME.5 DBTIME.4 DBTIME.3 DBTIME.2 DBTIME.1 DBTIME.0 SCTIME.1 SCTIME.0
Bit
Bit
MSB
–
DBTIME.5
DBTIME.4
DBTIME.3
DBTIME.2
DBTIME.1
DBTIME.0
SCTIME.1
SCTIME.0
HWSCEN
KEYDET
KYDTEN
KEYCLK
Symbol
Symbol
–
–
–
–
–
Debounce time in 4ms increments. 1 = 4ms de-bounce time, 0x3F =
252ms, 0x00 = 256ms. Key presses and key releases are debounced by
this amount of time.
Scan time in ms. 01 = 1ms, 02 = 2ms, 00 = 3ms, 00 = 4ms. Time between
checking each key during keypad scanning.
The current state of the keyboard clock can be read from this bit.
Hardware Scan Enable – When set, the hardware will perform automatic
key scanning. When cleared, the firmware must perform the key scanning
manually (bypass mode).
Key Detect – When HWSCEN = 1, this bit is set causing an interrupt that
indicates a valid key press was detected and the key location can be read
from the Keypad Column and Row registers. When HWSCEN = 0, this bit
is an interrupt which indicates a falling edge on any Row input if all Row
inputs had been high previously (note: multiple Key Detect interrupts may
occur in this case due to the keypad switch bouncing). In all cases, this bit
is cleared when read. When HWSCEN = 0 and the keypad interface 1kHz
clock is disabled, a key press will still set this bit and cause an interrupt.
Key Detect Enable – When set, the KEYDET bit can cause an interrupt and
when cleared the KEYDET cannot cause an interrupt. KEYDET can still
get set even if the interrupt is not enabled.
–
Table 66: The KSCAN Register
Table 67: The KSTAT Register
–
KEYCLK HWSCEN KEYDET
Function
Function
73S1210F Data Sheet
KYDTEN
LSB
LSB
65
Related parts for 73S1210F-44M/F/PC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
73S1210F Evaluation Board Lite
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC SMART CARD READER 44-QFN
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC SMART CARD READER 44-QFN
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC SMART CARD READER 68-QFN
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC SMART CARD READER 68-QFN
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC SMART CARD READER PROG 44-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC SMART CARD READER PROG 44-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC SMART CARD READER PROG 68-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC SMART CARD READER PROG 68-QFN
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Microcontrollers (MCU)
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Microcontrollers (MCU)
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Microcontrollers (MCU)
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Microcontrollers (MCU)
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Microcontrollers (MCU)
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Power Management Modules & Development Tools 73S1210F DEV KIT EVAL BD ICE CABLE CD
Manufacturer:
Maxim Integrated Products