EL1519CS Intersil, EL1519CS Datasheet - Page 8

no-image

EL1519CS

Manufacturer Part Number
EL1519CS
Description
IC LINE DRIVER CPE ADSL 8-SOIC
Manufacturer
Intersil
Type
Driverr
Datasheet

Specifications of EL1519CS

Number Of Drivers/receivers
1/0
Protocol
DSL
Voltage - Supply
5 V ~ 12 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EL1519CS
Manufacturer:
EL
Quantity:
27
Part Number:
EL1519CS
Manufacturer:
st
Quantity:
1 317
Part Number:
EL1519CS
Manufacturer:
ELANTEC
Quantity:
20 000
Part Number:
EL1519CS-T13
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
EL1519CS-T13
Quantity:
15 000
Capacitance at the Inverting Input
Due to the topology of the current feedback amplifier, stray
capacitance at the inverting input will affect the AC and
transient performance of the EL1519 when operating in the
non-inverting configuration.
In the inverting gain mode, added capacitance at the
inverting input has little effect since this point is at a virtual
ground and stray capacitance is therefore not “seen” by the
amplifier.
Feedback Resistor Values
The EL1519 has been designed and specified with
R
extremely flat frequency response with little to no peaking
out to 50MHz. As is the case with all current feedback
amplifiers, wider bandwidth, at the expense of slight
peaking, can be obtained by reducing the value of the
feedback resistor. Inversely, larger values of feedback
resistor will cause rolloff to occur at a lower frequency. See
the curves in the Typical Performance Curves section which
show 3dB bandwidth and peaking vs. frequency for various
feedback resistors and various supply voltages.
Bandwidth vs Temperature
Whereas many amplifier's supply current and consequently
3dB bandwidth drop off at high temperature, the EL1519 was
designed to have little supply current variations with
temperature. An immediate benefit from this is that the 3dB
bandwidth does not drop off drastically with temperature.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
F
=750Ω for A
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
V
= +5. This value of feedback resistor yields
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
For information regarding Intersil Corporation and its products, see www.intersil.com
8
EL1519
Supply Voltage Range
The EL1519 has been designed to operate with supply
voltages from ±2.5V to ±6V. Optimum bandwidth, slew rate,
and video characteristics are obtained at higher supply
voltages. However, at ±2.5V supplies, the 3dB bandwidth at
A
Single Supply Operation
If a single supply is desired, values from +5V to +12V can be
used as long as the input common mode range is not
exceeded. When using a single supply, be sure to either 1)
DC bias the inputs at an appropriate common mode voltage
and AC couple the signal, or 2) ensure the driving signal is
within the common mode range of the EL1519.
ADSL CPE Applications
The EL1519 is designed as a line driver for ADSL CPE
modems. It is capable of outputting 250mA of output current
with a typical supply voltage headroom of 1.3V. It can
achieve -85dBc of distortion at low 7.1mA of supply current
per amplifier.
The average line power requirement for the ADSL CPE
application is 13dBm (20mW) into a 100Ω line. The average
line voltage is 1.41V
ratio (crest factor) of 5.3 implies peak voltage of 7.5V into the
line. Using a differential drive configuration and transformer
coupling with standard back termination, a transformer ratio
of 1:2 is selected. The circuit configuration is as shown
below.
V
= +2 is a respectable 40MHz.
AFE
338Ω
+
+
-
-
1K
1K
RMS
. The ADSL DMT peak to average
12.5
12.5
TX1
1:2
April 10, 2007
FN7017.2
100

Related parts for EL1519CS