CY7C68000A-56LFXCT Cypress Semiconductor Corp, CY7C68000A-56LFXCT Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CY7C68000A-56LFXCT
Manufacturer Part Number
CY7C68000A-56LFXCT
Description
IC USB 2.0 TX2 TXRX 56VQFN
Manufacturer
Cypress Semiconductor Corp
Series
CY7Cr
Type
Transceiverr
Datasheet
1.CY7C68000A-56BAXC.pdf
(15 pages)
Specifications of CY7C68000A-56LFXCT
Protocol
USB 2.0
Voltage - Supply
3 V ~ 3.6 V
Mounting Type
Surface Mount
Package / Case
56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
CY3685 - KIT DEV EZ-USB NX2LPCY3683 - KIT EZ-USB TX2 DEVELOPMENT
Number Of Drivers/receivers
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Applications
Mobile Applications
■
■
■
■
■
■
Consumer Applications
■
■
■
■
Non-Consumer Applications
■
■
■
Functional Overview
The functionality of this chip is described in the following
sections:
USB Signaling Speed
The MoBL-USB TX2 operates at two of the rates defined in the
USB Specification 2.0, dated 4/27/2000.
■
■
The MoBL-USB TX2 does not support the LS signaling rate of
1.5 Mbps.
Transceiver Clock Frequency
The MoBL-USB TX2 has an on-chip oscillator circuit that uses
an external 24 MHz (±100 ppm) crystal with the following charac-
teristics:
■
■
■
■
Document #: 38-08052 Rev. *H
Smart Phones
PDA Phones
Gaming Phones
MP3 players
Portable Media Players (PMP)
GPS Tracking Devices
Cameras
Scanners
DSL Modems
Memory Card Readers
Networking
Wireless LAN
Home PNA
Full speed, with a signaling bit rate of 12 Mbps
High speed, with a signaling bit rate of 480 Mbps
Parallel resonant
Fundamental mode
500 μW drive level
27 to 33 pF (5% tolerance) load capacitors
An on-chip phase-locked loop (PLL) multiplies the 24 MHz oscil-
lator up to 30 or 60 MHz, as required by the transceiver parallel
data bus. The default UTMI interface clock (CLK) frequency is
determined by the DataBus16_8 pin.
Buses
The two packages enable a 8- or 16-bit bidirectional data bus for
data transfers to a controlling unit.
Suspend and Tristate Modes
When the MoBL-USB TX2 is not in use, the processor reduces
power consumption by putting it into Suspend mode using the
Suspend pin.
While in Suspend mode, Tristate mode may be enabled, which
tristates all outputs and I/Os, enabling the UTMI interface pins to
be shared with other devices. This is valuable in mobile handset
applications, where GPIOs are at a premium. The outputs and
I/Os are tristated ~50ns when Tristate mode is enabled, and are
driven ~50ns when Tri-state mode is disabled. All inputs must not
be left floating while in Tristate mode.
When resuming after a suspend, the PLL stabilizes approxi-
mately 200 μs after the suspend pin goes high.
Reset Pin
An input pin (Reset) resets the chip. This pin has hysteresis and
is active HIGH according to the UTMI specification. The internal
PLL stabilizes approximately 200 μs after V
Line State
The Line State output pins LineState[1:0] are driven by combina-
tional logic and may be toggling between the ‘J’ and the ‘K’
states. They are synchronized to the CLK signal for a valid
signal. On the CLK edge, the state of these lines reflect the state
of the USB data lines. Upon the clock edge the ‘0’ bit of the
LineState pins is the state of the DPLUS line and the ‘1’ bit of
LineState is the DMINUS line. When synchronized, the setup
and hold timing of the LineState is identical to the parallel data
bus.
Full Speed versus High Speed Select
The FS versus HS is done through the use of both XcvrSelect
and the TermSelect input signals. The TermSelect signal enables
the 1.5 Kohm pull up on to the DPLUS pin. When TermSelect is
driven LOW, a SE0 is asserted on the USB providing the HS
termination and generating the HS Idle state on the bus. The
XcvrSelect signal is the control that selects either the FS trans-
ceivers or the HS transceivers. By setting this pin to a ‘0’ the HS
transceivers are selected and by setting this bit to a’1’ the FS
transceivers are selected.
CY7C68000A
CC
has reached 3.3V.
Page 2 of 15
[+] Feedback