AT24C16C-PUM Atmel, AT24C16C-PUM Datasheet
AT24C16C-PUM
Specifications of AT24C16C-PUM
Available stocks
Related parts for AT24C16C-PUM
AT24C16C-PUM Summary of contents
Page 1
... The AT24C16C is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-lead UDFN, 8-lead XDFN, 5-lead SOT23, and 8-ball VFBGA Packages and is accessed via a Two-wire serial interface. In addition, the AT24C16C operates from 1.7V to 5.5V. Figure 0-1. Pin Configurations ...
Page 2
... DC Output Current .............................................. 5.0 mA Figure 0-2. Block Diagram VCC GND WP START SCL STOP SDA LOGIC LOAD DEVICE ADDRESS COMPARATOR Atmel AT24C16C 2 *NOTICE: SERIAL EN H.V. PUMP/TIMING CONTROL LOGIC COMP DATA RECOVERY LOAD INC R/W DATA WORD ADDR/COUNTER Y DEC OUT Stresses beyond those listed under “Absolute Maximum Ratings” ...
Page 3
... DEVICE/PAGE ADDRESSES: The Atmel number of devices on a single bus to one. WRITE PROTECT (WP): The AT24C16C has a write protect pin that provides hardware data protection. The write protect pin allows normal read/write operations when connected to ground (GND). When the write protect pin is connected to V ...
Page 4
... Memory Organization Atmel AT24C16C, 16K SERIAL EEPROM: Internally organized with 128 pages of 16-bytes each, the 16K requires an 11-bit data word address for random word addressing. Table 2-1. Pin Capacitance Applicable over recommended operating range from T Symbol Test Condition C Input/Output Capacitance (SDA) ...
Page 5
... V AI Min 1.3 0.6 (1) 0.05 1.3 (1) 0.6 0.6 0 100 (1) (1) 0 1.3 kΩ (2.5V, 5.0V), 10 kΩ (1.7V 0 Atmel AT24C16C = +1.7V to +5.5V 100 pF CC 1.7V 2.5V, 5.0V Max Min Max 400 1000 0.4 0 0.9 0.05 0.55 0.5 0.25 0.25 0 100 0.3 ...
Page 6
... Clock nine cycles 3. Create another start bit followed by stop bit condition as shown below Figure 3-1. Software Reset Start bit SCL SDA Atmel AT24C16C 6 ® AT24C16C features a low-power standby mode which is enabled: Dummy Clock Cycles Start bit 8 9 8719A–SEEPR–9/10 Stop bit ...
Page 7
... HIGH LOW t t HD.STA HD.DAT t AA ACK STOP CONDITION is the time from a valid stop condition of a write sequence to the end of the internal WR DATA STABLE DATA STABLE DATA CHANGE Atmel AT24C16C t LOW t SU.DAT START CONDITION SU.STO t BUF 7 ...
Page 8
... Figure 3-5. Start and Stop Definition SDA SCL START Figure 3-6. Output Acknowledge 1 SCL DATA IN DATA OUT START Atmel AT24C16C 8 STOP 8 9 ACKNOWLEDGE 8719A–SEEPR–9/10 ...
Page 9
... The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero allowing the read or write sequence to continue. 8719A–SEEPR–9/10 Atmel AT24C16C , to the nonvolatile memory. All inputs are disabled during this WR ...
Page 10
... The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (see <blue>Figure 6-6 on page 11). Figure 6-1. Device Address 16K MSB Figure 6-2. Byte Write DEVICE R T ADDRESS SDA LINE Atmel AT24C16C 10 P R/W 0 LSB WORD ADDRESS DATA ...
Page 11
... Figure 6-5. Random Read DEVICE R T ADDRESS SDA LINE Figure 6-6. Sequential Read R E DEVICE A ADDRESS D SDA LINE 8719A–SEEPR–9/ WORD ADDRESS (n) DATA ( DATA WORD DEVICE ADDRESS n T ADDRESS DUMMY WRITE DATA n DATA Atmel AT24C16C DATA ( DATA ( DATA DATA DATA ...
Page 12
... Ordering Code Detail Atmel Designator Product Family Device Density 16 = 16k Device Revision 8. Part Markings Atmel AT24C16C-PUM (TOP SIDE ONLY MARK) |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| ATMEL |---|---|---|---|---|---|---|---| | PIN 1 INDICATOR (DOT) LINE 1: AT=ATMEL H=MATERIAL SET/GRADE YWW=DATE CODE LINE 2: 16C=AT24C16C, M=1.7V to 5.5V, @=COUNTRY OF ASSEMBLY LINE 3: ATMEL LOT NUMBER Atmel AT24C16C ...
Page 13
... Atmel AT24C16C-SSHM |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| ATMEL |---|---|---|---|---|---|---|---| | PIN 1 INDICATOR (DOT) LINE 1: ATML=ATMEL H=MATERIAL SET/GRADE YWW=DATE CODE LINE 2: 16C=AT24C16C, M=1.7 to 5.5V, @=COUNTRY OF ASSEMBLY LINE 3: ATMEL LOT NUMBER Atmel AT24C16C-XHM PIN 1 INDICATOR (DOT) | |---|---|---|---|---|---| * A T |---|---|---|---|---|---| 1 6 |---|---|---|---|---|---|---| ATMEL |---|---|---|---|---|---|---| LINE 1: AT=ATMEL, H=MATERIAL SET/GRADE, YWW=DATE CODE LINE 2: 16C=AT24C16C, M=1.7 to 5.5V, @=COUNTRY OF ASSEMBLY ...
Page 14
... |---|---|---| * | PIN 1 INDICATOR (DOT) LINE 1: 16C=AT24C16C LINE 2: Y=DATE CODE, XX=Trace Code Atmel AT24C16C-STUM TOP MARK |---|---|---|---|---| |---|---|---|---|---| * | PIN 1 INDICATOR (DOT) Top Mark: 16C=AT24C16C, M=1.7v to 5.5V, U=MATERIAL SET/GRADE BOTTOM SIDE MARKING |---|---|---|---| |---|---|---|---| Bottom Mark: YM=DATE CODE XX=Trace Code Atmel AT24C16C-CUM |---|---|---|---| |---|---|---|---| |---|---|---|---| |<-- PIN 1 This Corner ...
Page 15
... Ordering Codes Atmel AT24C16C Ordering Information Ordering Codes AT24C16C-PUM (Bulk Form Only) (1) AT24C16C-SSHM-B (NiPdAu Lead Finish) (2) AT24C16C-SSHM-T (NiPdAu Lead Finish) (1) AT24C16C-XHM-B (NiPdAu Lead Finish) (2) AT24C16C-XHM-T (NiPdAu Lead Finish) (2) AT24C16C-MAHM-T (NiPdAu Lead Finish) (2) AT24C16C-MEHM-T (NiPdAu Lead Finish) (2) AT24C16C-STUM-T (matte Sn) (2) AT24C16C-CUM-T (matte Sn) ...
Page 16
... D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). Package Drawing Contact: packagedrawings@atmel.com Atmel AT24C16C Top View D ...
Page 17
... Package Drawing Contact: packagedrawings@atmel.com 8719A–SEEPR–9/ TITLE 8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) Atmel AT24C16C Ø Ø END VIEW COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 1.35 – ...
Page 18
... Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com Atmel AT24C16C TITLE 8A2, 8-lead 4 ...
Page 19
... Package Drawing Contact: packagedrawings@atmel.com 8719A–SEEPR–9/10 Pin 1 Index Area electrical connection TITLE 8Y6, 8-lead, 2.0x3.0 mm Body, 0.50 mm Pitch, UltraThin Mini-MAP, Dual No Lead Package (Sawn)(UDFN) Atmel AT24C16C (6X) A1 1.50 REF. COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM D 2.00 BSC E 3.00 BSC D2 1 ...
Page 20
... XDFN 8 7 PIN # Top View Package Drawing Contact: packagedrawings@atmel.com Atmel AT24C16C Side View TITLE 8ME1, 8-lead (1.80 x 2.20 mm Body) Extra Thin DFN (XDFN PIN # Bottom View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – 0.40 A1 0.00 – ...
Page 21
... Package Drawing Contact: packagedrawings@atmel.com 8719A–SEEPR–9/ Top View Side View TITLE 5TS1, 5-lead, 1.60 mm Body, Plastic Thin Shrink Small Outline Package (Shrink SOT) Atmel AT24C16C End View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – 1.10 0.10 A1 0.00 – 1. ...
Page 22
... PIN 1 BALL PAD CORNER Notes: 1. This drawing is for general information only. 2. Dimension ‘b’ is measured at maximum solder ball diameter. 3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu. Package Drawing Contact: packagedrawings@atmel.com Atmel AT24C16C PIN 1 BALL PAD CORNER TOP VIEW (d1) ...
Page 23
... Revision History Doc. Rev. Date 8719A 09/2010 8719A–SEEPR–9/10 Comments Initial document release Atmel AT24C16C 23 ...
Page 24
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...