DS3150T Maxim Integrated Products, DS3150T Datasheet - Page 11
![IC LIU T3/E3/STS-1 48-TQFP](/photos/6/55/65521/48-lqfp_21-0054f_sml.jpg)
DS3150T
Manufacturer Part Number
DS3150T
Description
IC LIU T3/E3/STS-1 48-TQFP
Manufacturer
Maxim Integrated Products
Type
Line Interface Units (LIUs)r
Datasheet
1.DS3150T.pdf
(28 pages)
Specifications of DS3150T
Number Of Drivers/receivers
1/1
Protocol
DS3
Voltage - Supply
3.135 V ~ 3.465 V
Mounting Type
Surface Mount
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS3150T
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS3150T+
Manufacturer:
Maxim
Quantity:
126
Part Number:
DS3150T+
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS3150TN+
Manufacturer:
Maxim
Quantity:
852
Company:
Part Number:
DS3150TNC1+
Manufacturer:
AMOTECH
Quantity:
400 000
Transmit Driver Monitor. If the transmit driver monitor detects a faulty transmitter, it activates the
DM output pin. When the transmitter is tri-stated (TTS = 0), the transmit driver monitor is also disabled.
The transmitter is declared to be faulty when the transmitter outputs see a load of less than about 25W.
The DM pin is only available in the TQFP package.
Transmitter Jitter Generation (Intrinsic). The transmitter meets the jitter generation requirements
of all applicable standards, with or without the jitter attenuator enabled.
Transmitter Jitter Transfer. Without the jitter attenuator enabled in the transmit side, the transmitter
passes jitter through unchanged. With the jitter attenuator enabled in the transmit side, the transmitter
meets the jitter transfer requirements of all applicable telecommunication standards in
Figure
Table 1-C. DS3 Waveform Template
Table 1-D. DS3 Waveform Test Parameters and Limits
Rate
Line Code
Transmission Medium
Test Measurement Point
Test Termination
Pulse Amplitude
Pulse Shape
Unframed All-Ones Power Level at
22.368MHz
Unframed All-Ones Power Level at
44.736MHz
Pulse Imbalance of Isolated Pulses
TIME (IN UNIT INTERVALS)
1-8.
-0.85 £ T £ -0.68
-0.85 £ T £ -0.36
-0.68 £ T £ 0.36
-0.36 £ T £ 0.36
PARAMETER
0.36 £ T £ 1.4
0.36 £ T £ 1.4
LOWER CURVE
UPPER CURVE
44.736Mbps (±20ppm)
B3ZS
Coaxial cable (AT&T 734A or equivalent)
At the end of 0 to 450 feet of coaxial cable
75W (±1%) resistive
Between 0.36V and 0.85V
An isolated pulse (preceded by two zeros and
followed by one or more zeros) falls within the
curves listed in
Between -1.8dBm and +5.7dBm
At least 20dB less than the power measured at
22.368MHz
Ratio of positive and negative pulses must be
between 0.90 and 1.10
11 of 28
0.5 {1 + sin[(p/2)(1 + T/0.34)]} + 0.03
0.5 {1 + sin[(p/2)(1 + T/0.18)]} - 0.03
NORMALIZED AMPLITUDE
0.08 + 0.407e
SPECIFICATION
Table
EQUATIONS
-0.03
-0.03
0.03
1-C.
-1.84(T - 0.36)
Table
1-A. See