STK14CA8-N45 Cypress Semiconductor Corp, STK14CA8-N45 Datasheet - Page 13
![](/photos/31/34/313454/42832soic_sml.jpg)
STK14CA8-N45
Manufacturer Part Number
STK14CA8-N45
Description
Manufacturer
Cypress Semiconductor Corp
Type
NVSRAMr
Datasheet
1.STK14CA8-N45.pdf
(17 pages)
Specifications of STK14CA8-N45
Word Size
8b
Organization
128Kx8
Density
1Mb
Interface Type
Parallel
Access Time (max)
45ns
Operating Supply Voltage (typ)
3.3V
Package Type
SOIC
Operating Temperature Classification
Commercial
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
2.7V
Operating Temp Range
0C to 70C
Pin Count
32
Mounting
Surface Mount
Supply Current
50mA
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STK14CA8-N45
Manufacturer:
STK
Quantity:
20 000
Software STORE
Data can be transferred from the SRAM to the nonvolatile
memory by a software address sequence. The STK14CA8
software STORE cycle is initiated by executing sequential E
controlled or G controlled READ cycles from six specific address
locations in exact order. During the STORE cycle, previous data
is erased and then the new data is programmed into the nonvol-
atile elements. After a STORE cycle is initiated, further memory
inputs and outputs are disabled until the cycle is completed.
To initiate the software STORE cycle, the following READ
sequence must be performed:
When the sixth address in the sequence is entered, the STORE
cycle commences and the chip is disabled. It is important that
READ cycles and not WRITE cycles be used in the sequence
and that G is active. After the t
SRAM is again activated for READ and WRITE operation.
Software RECALL
Data can be transferred from the nonvolatile memory to the
SRAM by a software address sequence. A software RECALL
cycle is initiated with a sequence of READ operations in a
manner similar to the software STORE initiation. To initiate the
RECALL cycle, the following sequence of E controlled or G
controlled READ operations must be performed:
Internally, RECALL is a two-step procedure. First, the SRAM
data is cleared, and second, the nonvolatile information is trans-
ferred into the SRAM cells. After the t
SRAM is again ready for READ or WRITE operations. The
RECALL operation in no way alters the data in the nonvolatile
storage elements.
Document Number: 001-51592 Rev. *C
Read Address
Read Address
Read Address
Read Address
Read Address
Read Address
Read Address
Read Address
Read Address
Read Address
Read Address
Read Address
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8FC0
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4C63
STORE
Valid READ
Valid READ
Valid READ
Valid READ
Valid READ
Initiate STORE Cycle
cycle time is fulfilled, the
Valid READ
Valid READ
Valid READ
Valid READ
Valid READ
Initiate RECALL Cycle
RECALL
cycle time, the
Data Protection
The STK14CA8 protects data from corruption during low voltage
conditions by inhibiting all externally initiated STORE and
WRITE operations. The low voltage condition is detected when
V
If the STK14CA8 is in a WRITE mode (both E and W low) at
power up, after a RECALL, or after a STORE, the WRITE is
inhibited until a negative transition on E or W is detected. This
protects against inadvertent writes during power up or brown out
conditions.
Noise Considerations
The STK14CA8 is a high speed memory and so must have a high
frequency bypass capacitor of approximately 0.1 µF connected
between V
as possible. As with all high speed CMOS ICs, careful routing of
power, ground, and signals reduce circuit noise.
Best Practices
nvSRAM products have been used effectively for over 15 years.
While ease-of-use is one of the product’s main system values,
experience gained working with hundreds of applications has
resulted in the following suggestions as best practices:
■
■
■
■
CC
The nonvolatile cells in an nvSRAM are programmed on the
test floor during final test and quality assurance. Incoming
inspection routines at customer or contract manufacturer’s
sites sometimes reprograms these values. Final NV patterns
are typically repeating patterns of AA, 55, 00, FF, A5, or 5A.
End product’s firmware should not assume an NV array is in a
set programmed state. Routines that check memory content
values to determine first time system configuration, cold or
warm boot status, and so on. should always program a unique
NV pattern (for example, complex 4-byte pattern of 46 E6 49
53 hex or more random bytes) as part of the final system
manufacturing test to ensure these system routines work
consistently.
Power up boot firmware routines should rewrite the nvSRAM
into the desired state such as AutoStore enabled. While the
nvSRAM is shipped in a preset state, best practice is to again
rewrite the nvSRAM into the desired state as a safeguard
against events that might flip the bit inadvertently (program
bugs, incoming inspection routines, and so on.)
If AutoStore is firmware disabled, it does not reset to “AutoStore
enabled” on every power down event captured by the nvSRAM.
The application firmware should re-enable or re-disable
AutoStore on each reset sequence based on the behavior
desired.
The V
and a maximum value size. Best practice is to meet this
requirement and not exceed the max V
nvSRAM internal algorithm calculates V
on this max Vcap value. Customers that want to use a larger
V
time should discuss their V
understand any impact on the V
a t
cap
<V
RECALL
SWITCH
value to make sure there is extra store charge and store
cap
CC
value specified in this data sheet includes a minimum
period.
.
and V
SS
, using leads and traces that are a short
cap
size selection with Cypress to
cap
voltage level at the end of
cap
cap
value because the
charge time based
STK14CA8
Page 13 of 17
[+] Feedback