JM38510/11202BPA National Semiconductor, JM38510/11202BPA Datasheet - Page 5

• Manufacturer Part Number: JM38510/11202BPA
• Manufacturer: National Semiconductor

Specifications of JM38510/11202BPA

• Number Of Elements: 2
• Output Type: Open Collector
• Technology: Bipolar
• Input Offset Voltage: 5@5VmV
• Single Supply Voltage (typ): 9/12/15/18/24/28V
• Dual Supply Voltage (typ): ±3/±5/±9/±12/±15V
• Supply Current (max): 2@5VmA
• Power Supply Requirement: Single/Dual
• Common Mode Rejection Ratio: 76dB
• Voltage Gain In Db: 93.98dB
• Single Supply Voltage (min): 5V
• Single Supply Voltage (max): 36V
• Dual Supply Voltage (min): ±2.5V
• Dual Supply Voltage (max): ±18V
• Power Dissipation: 400mW
• Operating Temp Range: -55C to 125C
• Operating Temperature Classification: Military
• Mounting: Through Hole
• Pin Count: 8
• Package Type: CDIP
• Lead Free Status / Rohs Status: Not Compliant

Symbol
∆I
A
V
Symbol
t
t
CS
RLH
RHL
VS
Lat
LM193 JAN Electrical Characteristics
DC Parameters
IO
AC Parameters
The following conditions apply, unless otherwise specified. +V
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
to ambient thermal resistance), and T
number given in the Absolute Maximum Ratings, whichever is lower.
Note 3: Short circuits from the output to V
current is approximately 20 mA independent of the magnitude of V
Note 4: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3V
Note 5: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the magnitude of the negative power supply,
if used).
Note 6: Human body model, 1.5KΩ in series with 100pF.
Note 7: S/S R
Note 8: K in datalog is equivalent to V/mV.
Note 9: Calculated parameter for ∆V
/ ∆T
Parameter
Temperature Coefficient of
Input Offset Current
Open Loop Voltage Gain
Voltage Latch (Logical "1"
Input)
Parameter
Response Time
Response Time
Channel Separation
S
= 20KΩ, tested with R
DC
.
(Continued)
IO
A
S
(ambient temperature). The maximum allowable power dissipation at any temperature is P
/ ∆T and ∆I
= 100KΩ for better resolution
+
can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
IO
/ ∆T.
Conditions
25˚C ≤ T
-55˚C ≤ T
+V
R
1V ≤ V
+V
V
Conditions
V
V
V
V
V
V
V
V
+V
A to B
+V
B to A
I
I
OD
I
OD
I
OD
I
OD
L
CC
CC
= 10V, I
= 100mV, R
= 100mV, R
= 100mV, R
= 100mV, R
CC
CC
= 15KΩ,
= 5mV
= 50mV
= 5mV
= 50mV
= 15V, -V
= 5V, -V
= 20V, -V
= 20V, -V
O
+
A
.
≤ 11V
A
≤ +125˚C
O
≤ 25˚C
= 4mA
CC
L
L
L
L
CC
CC
CC
= 5.1KΩ,
= 5.1KΩ,
= 5.1KΩ,
= 5.1KΩ,
= 0V,
5
= 0V,
= -10V,
= -10V,
CC
(Continued)
= 5V, −V
CC
+
= 0V
(Note 9)
(Note 9)
(Note 8)
(Note 8)
Jmax
voltage level (or to ground for a large overdrive) for the time
Notes
Notes
(maximum junction temperature), θ
-300
-400
Min
Min
50
25
80
80
Max
Max
300
400
0.4
5.0
7.0
0.8
1.2
2.5
3.0
0.8
1.0
Dmax
= (T
pA/˚C
pA/˚C
V/mV
V/mV
Unit
Unit
µS
µS
µS
µS
µS
µS
µS
µS
dB
dB
V
Jmax
JA
(package junction
- T
www.national.com
A
)/θ
groups
groups
JA
7, 8B
7, 8B
7, 8B
7, 8B
Sub-
Sub-
5, 6
8A
8A
8A
8A
or the
2
3
4
9
7
7