PIC32MX675F512LT-80V/BG Microchip Technology, PIC32MX675F512LT-80V/BG Datasheet - Page 46
![512 KB Flash, 64 KB RAM, USB-OTG, Ethernet, 80 MHz, 10-Bit ADC, DMA 121 XBGA 10x](/photos/40/62/406286/landingpagemicrochippic32_sml.jpg)
PIC32MX675F512LT-80V/BG
Manufacturer Part Number
PIC32MX675F512LT-80V/BG
Description
512 KB Flash, 64 KB RAM, USB-OTG, Ethernet, 80 MHz, 10-Bit ADC, DMA 121 XBGA 10x
Manufacturer
Microchip Technology
Series
PIC® 32MXr
Datasheet
1.PIC32MX575F256H-80VPT.pdf
(256 pages)
Specifications of PIC32MX675F512LT-80V/BG
Processor Series
PIC32MX6xx
Core
MIPS
Data Bus Width
32 bit
Program Memory Type
Flash
Program Memory Size
512 KB
Data Ram Size
64 KB
Interface Type
USB, I2C, UART, RS-232, RS-485, SPI
Maximum Clock Frequency
80 MHz
Number Of Programmable I/os
5
Number Of Timers
5
Operating Supply Voltage
2.3 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
XBGA-100
Operating Temperature Range
- 40 C to + 85 C
Supply Current (max)
10 mA
Core Processor
MIPS32® M4K™
Core Size
32-Bit
Speed
80MHz
Connectivity
Ethernet, I²C, SPI, UART/USART, USB OTG
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
-
Eeprom Size
-
Ram Size
64K x 8
Voltage - Supply (vcc/vdd)
2.3 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC32MX675F512LT-80V/BG
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 46 of 256
- Download datasheet (6Mb)
PIC32MX5XX/6XX/7XX
2.8
Many MCUs have options for at least two oscillators: a
high-frequency primary oscillator and a low-frequency
secondary oscillator. Refer to
Configuration”
The oscillator circuit should be placed on the same side
of the board as the device. Also, place the oscillator cir-
cuit close to the respective oscillator pins, not exceed-
ing one-half inch (12 mm) distance between them. The
load capacitors should be placed next to the oscillator
itself, on the same side of the board. Use a grounded
copper pour around the oscillator circuit to isolate them
from surrounding circuits. The grounded copper pour
should be routed directly to the MCU ground. Do not
run any signal traces or power traces inside the ground
pour. Also, if using a two-sided board, avoid any traces
on the other side of the board where the crystal is
placed. A suggested layout is illustrated in
FIGURE 2-3:
DS61156G-page 46
External Oscillator Pins
for details.
SUGGESTED OSCILLATOR
CIRCUIT PLACEMENT
Section 8.0 “Oscillator
Main Oscillator
Guard Trace
Secondary
Guard Ring
Oscillator
Figure
2-3.
2.9
If MPLAB ICD 2, ICD 3 or REAL ICE is selected as
a debugger, it automatically initializes all of the
Analog-to-Digital input pins (ANx) as “digital” pins by
setting all bits in the ADPCFG register.
The bits in this register that correspond to the Analog-
to-Digital pins that are initialized by MPLAB ICD 2, ICD
3 or REAL ICE, must not be cleared by the user
application firmware; otherwise, communication errors
will result between the debugger and the device.
If your application needs to use certain ADC pins as
analog input pins during the debug session, the user
application must clear the corresponding bits in the
ADPCFG register during initialization of the ADC
module.
When MPLAB ICD 2, ICD 3 or REAL ICE is used as a
programmer, the user application firmware must cor-
rectly configure the ADPCFG register. Automatic initial-
ization of this register is only done during debugger
operation. Failure to correctly configure the register(s)
will result in all ADC pins being recognized as analog
input pins, resulting in the port value being read as a
logic ‘0’, which may affect user application functionality.
2.10
Unused I/O pins should not be allowed to float as
inputs. They can be configured as outputs and driven
to a logic-low state.
Alternatively, inputs can be reserved by connecting the
pin to V
the pin as an input.
SS
Configuration of Analog and
Digital Pins During ICSP
Operations
Unused I/Os
through a 1k to 10k resistor and configuring
© 2009-2011 Microchip Technology Inc.
Related parts for PIC32MX675F512LT-80V/BG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-4.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.85VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: