TCS3414FN TAOS, TCS3414FN Datasheet - Page 5

• Manufacturer Part Number: TCS3414FN
• Description: Photodiodes TRI Color Sensor LTD I2C 6 Pin ODFN
• Manufacturer: TAOS
• Type: Digital Color Sensorr

Specifications of TCS3414FN

• Photodiode Material: InGaN
• Peak Wavelength: 640 nm
• Maximum Rise Time: 300 ns
• Maximum Fall Time: 300 ns
• Package / Case: DFN-6
• Mounting Style: SMD/SMT
• Product: Ambient Light Sensor
• Lead Free Status / Rohs Status: Details

Optical Characteristics, V
Notes 1 and 2)
NOTES: 1. The percentage shown represents the ratio of the respective red, green, or blue channel value to the clear channel value.
Operating Characteristics, V
NOTES: 1. At shorter integration times and/or higher Prescale settings, the device will reach saturation of the analog section before the digital
The LUMENOLOGY r Company
R
R
f
osc
e
e
PARAMETER
PARAMETER
Irradiance
responsivity
(CS
package)
package)
Irradiance
responsivity
(FN
package)
package)
Gain scaling, relative to 1
Gain scaling, relative to 1
Dark ADC count value
Maximum digital count value
Oscillator frequency
Internal integration time tolerance
Temperature coefficient of responsivity (SYNC mode)
2. Optical measurements are made using small-angle incident radiation from a light-emitting diode (LED) optical source.
3. The 470 nm input irradiance is supplied by an InGaN light-emitting diode with the following characteristics:
4. The 524 nm input irradiance is supplied by an InGaN light-emitting diode with the following characteristics:
5. The 640 nm input irradiance is supplied by a AlInGaP light-emitting diode with the following characteristics:
6. Illuminance responsivity R
2. Gain is controlled by the gain register (07h) described in the Register section.
3. Measurements taken when the Photodiode field value in the Photodiode Register (06h) is 00b and when the Prescaler field value
4. The full scale ADC count value is slew-rate limited for short integration times and is limited by the 16-bit counter for long integration
peak wavelength λ
peak wavelength λ
peak wavelength λ
notes 3, 4, and 5 and using 1 lx = 1 lm/m
count reaches the maximum 16-bit value. The worst-case (lowest) analog saturation value can be obtained using the formula: Analog
saturation = (fosc(min)
time (internal, manually-timed, or sync-generated) in seconds.
in the Gain Register (07h) is 000b.
times. The nominal transition between the two regions is t
λ
See Note 3
λ
See Note 4
λ
See Note 5
λ
See Note 3
λ
See Note 4
λ
See Note 5
CONDITIONS
p
p
p
p
p
p
= 470 nm,
= 524 nm,
= 640 nm,
= 470 nm,
= 524 nm,
= 640 nm,
PARAMETER
TEST
TEST
p
p
p
×
×
= 470 nm, spectral halfwidth Δλ½ = 35 nm, and luminous efficacy = 75 lm/W.
= 524 nm, spectral halfwidth Δλ½ = 47 nm, and luminous efficacy = 520 lm/W.
= 640 nm, spectral halfwidth Δλ½ = 17 nm, and luminous efficacy = 155 lm/W.
gain setting
gain setting
×
DD
Tint)
80%
80%
MIN
0%
0%
0%
0%
v
= 3 V, T
Red Channel
DD
is calculated from the irradiance responsivity R
÷
Prescale, where Fosc(min) is the minimum oscillator frequency in Hz, and tint is the actual integration
TYP
= 3 V, T
A
r
= 255C, GAIN = 64y, Tint = 12ms (unless otherwise noted) (see
110%
110%
MAX
15%
15%
15%
15%
2
.
A
4
16
64
×
www.taosinc.com
= 255C, (unless otherwise noted) (see Notes 2, 3, and 4)
×
×
15%
60%
10%
60%
MIN
0%
0%
Green Channel
E
Prescale = 1, T
λ  700 nm, − 40°C  T
e
= 0, 64
TYP
int
TEST CONDITIONS
×
= 65535/5000 = 13.1 ms.
gain setting, T
MAX
50%
90%
15%
50%
90%
15%
int
= 400 ms (Note 1)
65%
65%
MIN
0%
0%
0%
0%
Blue Channel
e
A
by using the LED luminous efficacy values stated in
int
 85°C
TYP
= 400 ms
r
DIGITAL COLOR SENSORS
MAX
90%
35%
15%
90%
35%
15%
15.2
60.8
MIN
59.0
71.2
80.6
56.3
72.5
94.2 105.3
MIN
3.8
4.2
−5
Clear Channel
0
TCS3404, TCS3414
± 200
Copyright E 2011, TAOS Inc.
TYP
TYP
65.6
76.9
90.1
62.5
78.4
4.4
16
64
TAOS137A − APRIL 2011
4
3
65535
116.3
MAX
MAX
72.5
82.7
99.5
69.1
84.3
16.8
67.2
4.2
4.6
15
5
(counts/
(counts/
ppm/°C
counts
counts
UNIT
UNIT
UNIT
MHz
cm
cm
cm
cm
μW/
μW/
%
2
2
2
2
)
)
)
)
5