LM70CIMMX-5/HALF National Semiconductor, LM70CIMMX-5/HALF Datasheet
LM70CIMMX-5/HALF
Specifications of LM70CIMMX-5/HALF
LM70CIMMX-5/HALF Summary of contents
Page 1
... System Thermal Management n Personal Computers n Disk Drives n Office Electronics n Electronic Test Equipment Simplified Block Diagram © 2006 National Semiconductor Corporation Features n 0.25˚C temperature resolution. n Shutdown mode conserves power between temperature reading n SPI and MICROWIRE Bus interface n MSOP-8 and LLP-8 packages save space ...
Page 2
... Order Number Marking LM70CILD-3 T33 LM70CILDX-3 T33 LM70CILD-5 T35 LM70CILDX-5 T35 LM70CIMM-3 T04C LM70CIMMX-3 T04C LM70CIMM-5 T03C LM70CIMMX-5 T03C Pin Descriptions Label SOP-8 LLP-8 Pin # Pin # SI Input/Output - Serial bus bi-directional data line. Schmitt trigger input Clock - Serial bus clock Schmitt trigger input line ...
Page 3
Typical Application FIGURE 1. COP Microcontroller Interface 3 10122303 www.national.com ...
Page 4
Absolute Maximum Ratings Supply Voltage Voltage at any Pin Input Current at any Pin (Note 2) Package Input Current (Note 2) Storage Temperature Soldering Information, Lead Temperature MSOP-8 and LLP-8 Packages (Note 3) Vapor Phase (60 seconds) Infrared (15 seconds) ...
Page 5
Logic Electrical Characteristics Serial Bus Digital Switching Characteristics Unless otherwise noted, these specifications apply for V LM70-5, C (load capacitance) on output lines = 100 pF unless otherwise specified. Boldface limits apply for all other ...
Page 6
... Note 3: See the section titled “Surface Mount” found in a current National Semiconductor Linear Data Book for other methods of soldering surface mount devices. ...
Page 7
Electrical Characteristics FIGURE 5. Temperature-to-Digital Transfer Function (Non-linear scale for clarity) TRI-STATE Test Circuit (Continued) FIGURE 6. 7 10122308 10122307 www.national.com ...
Page 8
Typical Performance Characteristics Average Power-On Reset Voltage vs Temperature Temperature Error www.national.com Static Supply Current vs Temperature 10122323 10122322 8 10122321 ...
Page 9
... FF hex (Shutdown, transmit manufacturer’s ID) . any others may place the part into a Test Mode. Test Modes are used by National Semiconductor to thoroughly test the function of the LM70 during production testing. Only eight bits have been defined above since only the last eight trans- ...
Page 10
... D0–D1: Undefined. TRI-STATE will be output on SI/0. D2-D4: Always set LOW. www.national.com (Continued) D10 will stop responding as described. These test modes are to be used for National Semiconductor production testing only. See Section 1.2 Serial Bus Interface for a complete discus- sion. D10 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 D5– ...
Page 11
Serial Bus Timing Diagrams a) Reading Continuous Conversion - Single Eight-Bit Frame b) Reading Continuous Conversion - Two Eight-Bit Frames 3.0 Application Hints To get the expected results when measuring temperature with an integrated circuit temperature sensor like the ...
Page 12
Typical Applications FIGURE 8. Temperature monitor using Intel 196 processor FIGURE 9. LM70 digital input control using micro-controller’s general purpose I/O. www.national.com 10122320 12 10122319 ...
Page 13
... Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead Molded Mini Small Outline Package (MSOP) Order Number LM70CIMM-3, LM70CIMMX-3, LM70CIMM-5 or LM70CIMMX-5 Order Number LM70CILD-3, LM70CILDX-3, LM70CILD-5 or LM70CILDX-5 (JEDEC REGISTRATION NUMBER M0-187) NS Package Number MUA08A 8-Lead Molded Leadless Leadframe Package NS Package Number LDA08A 13 www ...
Page 14
... BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. ...