LF1E-D3S-2N IDEC Corporation, LF1E-D3S-2N Datasheet - Page 8

• Manufacturer Part Number: LF1E-D3S-2N
• Description: LED; LF1E LIGHT STRIP WHITE 24V DC LENGTH 1066 MM NO LENS
• Manufacturer: IDEC Corporation
• Type: LED/Steadyr

Specifications of LF1E-D3S-2N

• Color: White
• Length: 1066 mm
• Mounting Type: Surface
• Primary Type: Light Strip
• Rating: IP54
• Lead Free Status / Rohs Status: RoHS Compliant part

Specifications and other descriptions in this catalog are subject to change without notice.
www.idec.com
•
•
•
•
•
•
•
•
•
•
Do not disassemble, repair, or modify illumination units.
Turn off power to the illumination units before wiring. Make
Do not stare directly into the illumination unit while it is lit, and
Before designing final equipment and powering up illumination
units, confirm the specifications described on the instruction
sheet. If there is any uncertainty, contact IDEC before
powering up illumination units.
Apply voltage within the rated value, otherwise the LED
elements may be damaged.
The illumination unit is vulnerable to static electricity. Take
sufficient measure for protection against static electricity and
voltage surges.
Make sure that the illumination unit does not fall during
transportation, installation, and operation, otherwise damage
may result.
Do not pull or push the cable of the illumination unit, otherwise
damage may result. Allow sufficient slack to the cable while
wiring.
Do not apply excessive force to the illumination unit. Do
not leave a damaged illumination unit unattended or use a
damaged illumination unit.
Ensure the correct operating temperature around the
illumination unit. Otherwise internal temperature rise may
result in damage.
Otherwise electric shock, fire, or malfunction may occur.
sure of correct wiring, otherwise electric shock or damage
may result.
Instructions
Safety Precautions
IDEC CORPORATION (USA)
1175 Elko Drive, Sunnyvale, CA 94089-2209, USA
Tel: [phone] / (800) 262-IDEC (4332)
Fax: [phone]
E-mail: [e-mail]
IDEC CANADA LIMITED
3155 Pepper Mill Court, Unit 4, Mississauga,
Ontario, L5L 4X7, Canada
Tel: [phone], Toll Free: [phone]
Fax: [phone]
E-mail: [e-mail]
IDEC AUSTRALIA PTY. LTD.
2/3 Macro Court, Rowville, Victoria 3178, Australia
Tel: [phone], Toll Free: 1800-68-4332
Fax: [phone]
E-mail: [e-mail]
IDEC ELECTRONICS LIMITED
Unit 2, Beechwood, Chineham Business Park,
Basingstoke, Hampshire RG24 8WA, UK
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
TM
LF1D/LF2D LED Illumination Units
Tel: [phone], Fax: [phone]
IDEC ELEKTROTECHNIK GmbH
Wendenstrasse 331, 20537 Hamburg, Germany
Tel: [phone] - 0, Fax: [phone] - 24
E-mail: [e-mail]
IDEC (SHANGHAI) CORPORATION
Room 608-609, 6F, Gangtai Plaza, No. 700,
Yan'an East Road, Shanghai 200001, PRC
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC (BEIJING) CORPORATION
Room 211B, Tower B, The Grand Pacific Building,
8A Guanghua Road, Chaoyang District,
Beijing 100026, PRC
Tel: [phone], Fax: [phone]
IDEC (SHENZHEN) CORPORATION
Unit AB-3B2, Tian Xiang Building, Tian’an Cyber Park,
Fu Tian District, Shenzhen, Guang Dong 518040, PRC
•
•
•
•
•
•
The illumination unit is a general-purpose
do not project the light to other people, otherwise eyes may
be injured.
device. Do not use the illumination unit for electronic
equipment which may damage the human body or threaten
life in case a malfunction or failure occurs.
Do not use or store the illumination unit in a place subjected to
vibration and shock.
Do not use the illumination unit in the following places:
Do not loosen screws, otherwise the protection characteristics
will be impaired.
For the LF2D illumination units, make sure to a provide
sufficient strength for mounting panel. Required waterproof
characteristics cannot be obtained if a distorted mounting
panel is used.
Use illumination units with a Class 2 power supply.
∗ Exposed to direct sunlight, near heaters, and at high tem-
∗ Subject to chemicals, and corrosive gases (Plastic illumina-
∗ Basements, greenhouses, or other humid places
∗ Cold storage warehouses and cooler exhaust outlets (make
7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
peratures
tion surface types: Iron powder and oil)
sure that no freezing occurs)
Cat. No. EP1307-0 JUNE 2010 PDF
IDEC IZUMI (H.K.) CO., LTD.
Units 11-15, Level 27, Tower 1,
Millennium City 1, 388 Kwun Tong Road,
Kwun Tong, Kowloon, Hong Kong
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC TAIWAN CORPORATION
8F-1, No. 79, Hsin Tai Wu Road, Sec. 1,
Hsi-Chih, Taipei County, Taiwan
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC IZUMI ASIA PTE. LTD.
No. 31, Tannery Lane #05-01,
HB Centre 2, Singapore 347788
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
industrial electric
(100611)