QS30ARX BANNER ENGINEERING, QS30ARX Datasheet - Page 3

• Manufacturer Part Number: QS30ARX
• Description: SENSOR; PHOTOELECTRIC; HIGH-POWERED RECEIVER; INFRARED; RANGE 213 M; 10-30VDC
• Manufacturer: BANNER ENGINEERING
• Type: Infraredr

Specifications of QS30ARX

• Brand/series: World-Beam®
• Current, Switching: 100 mA
• Ip Rating: IP67
• Mounting Type: Threaded
• Output: NPN/PNP
• Primary Type: Photoelectric
• Range, Measurement: 213 m
• Sensing Mode: Opposed
• Technology: Photoelectric
• Termination: 5-Wire Cable
• Voltage, Supply: 30 VDC

Specifications
Dimensions
WORLD-BEAM® QS30 Series Sensors
P/N 115011 Rev. C
Supply Voltage and Current
Beam
Sensing Range
Output Configuration
Output Rating:
Output Response
Adjustments
9.0 mm
(0.35")
Emitter: 10 to 30V dc (10% maximum ripple) at
less than 70 mA
Receiver: 10 to 30V dc (10% maximum ripple) at
less than 22 mA (exclusive of load)
875 nm, infrared
Excess gain of 2 at 213 m (700')
Bipolar current sinking (NPN) white wire; current
sourcing (PNP) black wire
100 mA max
OFF-state leakage current: less than 200 µA
ON-state saturation voltage: less than 1.5V @
100 mA, less than 900 millivolts at 10 mA
Protected against false power-up and continuous
overload or short circuit of outputs
30 milliseconds ON and 30 milliseconds OFF; 5
ms repeatability
Light Operate/Dark Operate — dependent on
model selected
Frequency via gray wire
Emitter only: LED inhibit via white wire White (-)
turns emitter LED OFF (to allow verification of sen-
sor operation)
21 mm
(0.83")
A: Gray (+)
B: Gray (-)
Cabled Models
43.0 mm
(1.69")
32.5 mm
(1.28")
Bracket dimensions are shown on page 5.
5.0 mm
(0.20")
www.bannerengineering.com - tel: [phone]
22.0 mm
(0.87")
2 x ø3.3 mm (0.125")
Indicators
Environmental Rating
Construction
Connection
Operating Conditions
Mounting Torque
Certifications
Application Notes
0.7 Nm (6 in lbs)
3.5 mm
Green LED: Power ON
Frequency indicator (A or B)
Receiver only:
Yellow LED: Output conducting
4-LED Signal Strength light bar
Cabled models: IP67, NEMA 6P
QD models: IP69K per DIN 40050-9
ABS plastic housing; impact-resistant lens material
5-wire cable (2 m or 9 m) or 5-pin integral Euro-style quick-
disconnect fitting
Temperature: -20° to +60° C (-4° to +140° F)
Relative Humidity: 90%; non-condensing
Maximum 4.5 Nm (40 in lbs) with included 30 mm mounting
nut
(0.14")
1. When multiple sensors are used in close proximity,
2. Prolonged outdoor use in direct sunlight may cloud
max. torque
position sensors such that the alternate frequency
emitter is not within the receiver's field of view. Con-
tact the Banner Application team for additional infor-
mation.
the lens. Contact Banner for other outdoor solutions.
34.0 mm
(1.34")
M30 x 1.5 Thread
max. torque
6 Nm (53 in lbs)
with included 30 mm
mounting nut
33.0 mm
(1.30")
12.5 mm
(0.49")
QD Models
13.0 mm
44.0 mm
1.3 mm
(0.05")
(1.73")
(0.51")
3