AAT3113ITP-20-T1 Analogic Tech, AAT3113ITP-20-T1 Datasheet - Page 8

• Manufacturer Part Number: AAT3113ITP-20-T1
• Description: Switching Converters, Regulators & Controllers High Efficiency 1.5x Fractional Chrg Pump
• Manufacturer: Analogic Tech

Specifications of AAT3113ITP-20-T1

• Output Voltage: 6 V (Max)
• Output Current: 150 mA (Max)
• Input Voltage: 2.7 V
• Switching Frequency: 600 KHz
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Package / Case: TSOPJW-12
• Number Of Outputs: 4
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Functional Block Diagram
Functional Description
The AAT3113 and AAT3114/14A devices are high effi-
ciency 1.5X fractional charge pumps intended for white
LED backlight applications. The fractional charge pump
consists of a linear regulator followed by a 1.5X charge
pump. The AAT3113 and AAT3114/14A require only four
external components: two 1µF ceramic capacitors for the
charge pump flying capacitors (C1 and C2), one 1µF
ceramic capacitor for C
ic capacitor for C
verted into four or six constant current outputs (D1 to
D4 or D6) to drive four or six individual LEDs with a
maximum of 20mA each. The current source output
magnitude is controlled by the EN/SET serial data
S
8
8
ChargePump
ChargePump
2
Cwire interface. The interface records rising edges of
OUT
TM
TM
. The charge pump output is con-
IN
High Efficiency 1.5X Fractional Charge Pumps For White LED Applications
High Efficiency 1.5X Fractional Charge Pumps For White LED Applications
EN/SET
, and one 0.33µF to 1µF ceram-
Interface
S
2
Cwire
GND
w w w . a n a l o g i c t e c h . c o m
w w w . a n a l o g i c t e c h . c o m
5
Reference
Soft Start
Oscillator
600kHz
Voltage
32x8 bit
ROM
AAT3113, AAT3114/14A
AAT3113, AAT3114/14A
the EN/SET pin and decodes them into 32 individual cur-
rent level settings each 1dB apart (see Table 1, Current
Level Settings). Code 32 is full scale, and Code 1 is full
scale attenuated by 31dB. The modulo 32 interface
wraps states back to state 1 after the 32nd clock. With
each EN/SET pulse, the output current increases by 1dB.
To decrease the output current by 1dB, 31 EN/SET clock
pulses are required. The counter can be clocked at
speeds up to 1MHz, so intermediate states are not visi-
ble. The first rising edge of EN/SET enables the IC and
initially sets the output LED current to -31dB, the lowest
setting equal to 525µA. Once the final clock cycle is input
for the desired brightness level, the EN/SET pin is held
high to maintain the device output current at the pro-
grammed level. The device is disabled 500µs after the
EN/SET pin transitions to a logic low state.
8
Charge
Pump
1.5X
VIN
* AAT3114/14A only
Current
Mode
DAC
PRODUCT DATASHEET
PRODUCT DATASHEET
C2+
C1+
C2-
OUT
D1
D2
D3
D4
D5*
D6*
C1-
3113.2008.05.1.10
3113.2008.05.1.10