MAX6651EEE-T Maxim Integrated Products, MAX6651EEE-T Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX6651EEE-T
Manufacturer Part Number
MAX6651EEE-T
Description
Motor / Motion / Ignition Controllers & Drivers
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX6650EUBT.pdf
(25 pages)
Specifications of MAX6651EEE-T
Operating Supply Voltage
3 V to 5.5 V
Package / Case
QSOP-16
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX6651EEE-T
Manufacturer:
RENESAS
Quantity:
4 022
Part Number:
MAX6651EEE-T
Manufacturer:
MAXIM/美信
Quantity:
20 000
across the fan until the desired speed is reached. Open-
loop operation allows the µC to regulate fan speed direct-
ly. The µC reads the fan speed from the Tach-
ometer-Count Register. Based on the tachometer
count, the µC decides if the fan speed requires adjust-
ment, and changes the voltage across the fan by writ-
ing an 8-bit word to the DAC Register. Full-on mode
applies the maximum voltage across the fan, forcing it
to spin at full speed. Configuring GPIO1 (see the
General-Purpose Input/Output section) as an active-low
input provides additional hardware control that fully
turns on the fan and overrides all software commands.
Fan-Speed Regulators and Monitors
with SMBus/I
Table 4. Configuration Byte Register
Figure 5. General-Purpose Input/Output Structure
10
7 (MSB) to 6
2 to 0 (LSB)
______________________________________________________________________________________
5 to 4
BIT
3
DEFINITION
REGISTER
REGISTER
STATUS
GPIO
GPIO
MAX6650
MAX6651
100kΩ
SCALE
NAME
MODE
5/12V
—
GPIO_
GND
V
CC
2
C-Compatible Interface
POR (DEFAULT)
C
BYPASS
STATE
V
3.0V TO 5.5V
010
CC
00
0
1
Always 0
Operating Mode:
00 = Software full-on (default)
01 = Software off (shutdown)
10 = Closed-loop operation
11 = Open-loop operation
Fan/Tachometer Voltage:
0 = 5V
1 = 12V (default)
Prescaler Division:
000 = Divide by 1
001 = Divide by 2
010 = Divide by 4 (default)
011 = Divide by 8
100 = Divide by 16
The GPIO pins connect to the drain of the internal N-
channel MOSFET and pullup resistor (Figure 5). When
the N-channel MOSFET is off (Table 5), the pullup resis-
tor provides a logic-level high output. However, with the
MOSFET off, the GPIO may serve as an input pin and
its state is read from the GPIO Status Register (Table
6). The MAX6650/MAX6651 power up with the MOSFET
off, so input signals may be safely connected to the
GPIO pins. When using the GPIO pin as a general-pur-
pose output, change the output by writing to the GPIO
Definition Register.
GPIO0 may be configured as an ALERT output that will
go low whenever a fault-condition is detected (see the
Alarm-Enable and Status Registers section). GPIO1
may be configured as a FULL ON input to allow hard-
ware control to fully turn on the fan in case of software
or µC failure. GPIO2 (MAX6651 only) may be config-
ured as an internal clock output or as an external clock
input to allow synchronization of multiple devices.
The alarms are enabled only when the appropriate bits of
the Alarm-Enable Register are set (Table 7). The maxi-
mum and minimum output level alarms function only
when the device is configured to operate in the closed-
loop mode (see the Configuration-Byte Register section).
The Alarm Status Register allows the system to deter-
mine which alarm caused the alert output (Table 8).
The set-alarm and alert outputs clear after reading the
Alarm-Enable and Status Registers
General-Purpose Input/Output
FUNCTION