K3HB-XAD24VACVDC Omron Automation, K3HB-XAD24VACVDC Datasheet
K3HB-XAD24VACVDC
Related parts for K3HB-XAD24VACVDC
K3HB-XAD24VACVDC Summary of contents
Page 1
... Only one of the following can be used by each Digital Indicator: RS-232C/RS-485 communications, a linear output, or DeviceNet communications. Accessories (Sold Separately) K32-DICN: Special Cable (for event inputs, with 8-pin connector) K32-BCD: Special BCD Output Cable CSM_K3HB-X_DS_E_4_1 Base Units with Optional Boards K3HB-X@-@@@ Sensor Power Supply/Output Type Code None: None CPA: Relay output (PASS: SPDT) + Sensor power supply (12 VDC +/− ...
Page 2
... DC power supply models. The OMRON S8VS-series DC Power Supply Unit is recommend- ed. 2. PNP input types are also available. 3. For K3HB-series DeviceNet models, use only the DeviceNet Connector included with the product. The crimp terminals provided are for Thin Cables. Load: 500 Ω max, Resolution: Approx. 10,000, Output error: ±0.5% FS Load: 5 kΩ ...
Page 3
... Power Frequency Magnetic Immunity EN61000-4-8: 30 A/m (50 Hz) continuous time Voltage Dips and Interruptions Immunity EN61000-4-11: 0.5 cycle, 0°/180°, 100% (rated voltage sweeps of 5 min each and Z directions 2 2 (100 m/s for relay outputs) 3 times each in 3 axes, 6 directions K3HB-X 3 ...
Page 4
... MΩ − E6 COM 4. The K3HB-XVA@@ complies with UL standards when the applied input voltage is within the range 0 to 150 VAC. If the input voltage is higher than 150 VAC, install an external transformer or take other measures to drop the voltage to 150 VAC or lower. Measurement range Input impedance ± ...
Page 5
... Error detection Vertical parity and FCS Parity check Odd, even Note: For details on serial and DeviceNet communications, refer to the Digital Indicator K3HB Communications User's Manual (Cat.No. N129). BANK4 --- ON residual voltage max. OFF leakage current: 1.5 mA max. Load current max. ...
Page 6
... Supplied from DeviceNet communications connector Keys Indications Drive Transistor circuit output Micro- computer Drive Relay output X circuit Drive DeviceNet DeviceNet circuit circuit Communi- Drive cations Communications circuit driver COM V O DC-DC Converter (isolated) K3HB-X Drop line length Total drop line (max.) length (max 156 m 6 ...
Page 7
... Turns ON when the tare zero function is T-ZR executed. Turns OFF not executed or is cleared. Turns ON when the forced-zero function is Zero executed. Turns OFF not executed or is cleared. (Excluding the K3HB-H.) Turns ON/OFF when hold input turns Hold ON/OFF. MAX/MIN Key LEVEL Key Used to switch the Used to switch level ...
Page 8
... V Refer to the following User's Manual for application precautions and other information required when using the Digital Indicator: K3HB-S/-X/-V/-H Digital Indicator User's Manual (Cat. No. N128) The manual can be downloaded from the following site in PDF format: OMRON Industrial Web http://www.fa.omron.co.jp Continuous Data Output REQ ...
Page 9
... K3HB-X 9 ...
Page 10
... Always use a EN/IEC-compliant power supply with reinforced insulation or double insulation for the DeviceNet power supply. • The product must be used indoors for the above applicable standards to apply. • The K3HB-XVA@@ complies with UL standards when the applied input voltage is within the range 0 to 150 VAC. K3HB-X B ...
Page 11
... XG4M-1030 (OMRON) • Special Cable (Sold separately) K32-DICN (OMRON) (XG4M-1030 with 3 m cable) BCD Output Cable Model K32-BCD K3HB end 38 mm Cover: HDR-E50LPA5 (manufactured by Honda Tsushin Co., Ltd.) Connector: HDR-E50MAG1 (manufactured by Honda Tsushin Co., Ltd.) Note: The BCD Output Cable has a D-sub plug. Cover: 17JE-37H-1A (manufactured by DDK); Connector: equivalent to 17JE-23370-02 (D1) (manufactured by DDK) ...
Page 12
... Previous Average Value Comparison Slight changes can be removed from input signals to detect only extreme changes. Input value 2 Input value 1 Input value (inp.a2) (inp.a1) (Reverse scaling) K3HB-X Sampling hold value ON Peak-to-peak value (b2−a2) (b1−a1) b1 'b2 a1 'a2 ...
Page 13
... If interruption memory is ON, the maximum and minimum values after the last resetting will be displayed. • If interruption memory is OFF, the maximum and minimum values will be displayed after the power supply is turned ON (or after the reset input is performed). Input Red 110.01 H 110.00 K3HB-X 13 ...
Page 14
... Terminal cover (included) 91 Character Size for Main Display (mm) PV display SV display 14.2 100 (112) 7.6 12 1.3 95 *DeviceNet models Terminal: M3, Terminal Cover: Accessory K3HB-X Hysteresis Hysteresis Input Startup H output compensation time set time H input Panel Cutout Dimensions 120 min. 4.9 3.5 75 min. +0 ...
Page 15
... Insert the adapter into the grooves on the left and right sides of the rear case and push until it reaches the panel and is fixed in place. Adapter ■ LCD Field of Vision The K3HB is designed to have the best visibility at the angles shown in the following diagram. 10° 30° ■ Rubber Packing ...
Page 16
... Doing so may occasionally result in minor or moderate injury due to electric shock. Do not use the equipment for measurements within Measurement Categories III and IV for K3HB-X and II, III, and IV for K3HB-S, K3HB-V, and K3HB-H (according to IEC61010-1). Doing so may occasionally cause unexpected operation, resulting in minor or moderate injury, or damage to the equipment ...
Page 17
... Reception interference may occur if the product is used close to a radio, television, or wireless. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. In the interest of product improvement, specifications are subject to change without notice. Digital Indicator Digital Indicator K3HB-X 17 ...
Page 18
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a ...