T520B476M010ATE035/BKN Kemet, T520B476M010ATE035/BKN Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/365/kemet_sml.jpg)
T520B476M010ATE035/BKN
Manufacturer Part Number
T520B476M010ATE035/BKN
Description
CAPACITOR, TANTALUM SMD CONDUCTIVE POLYMER, KO-CAP, 47UF 10V 20%, CUT TAPE
Manufacturer
Kemet
Datasheet
1.T520V337M2R5ATE025BKN.pdf
(7 pages)
Specifications of T520B476M010ATE035/BKN
Capacitance
47 μF
Case Code
B
Case Size
A,T,B,C,W,V,D,Y & X
Esr
35 Milliohms
Esr, Test Condition
@ +25°C,100 kHz
Material, Element
Tantalum
Termination
SMT
Tolerance
±10% & ±20%
Voltage, Rating
10 VDC
Capacitance Range
15uF - 1000uF
Voltage Range
2 - 25V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
1. B1 dimension is a reference dimension for tape feeder clearance only.
2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
3. Tape with components shall pass around radius “R” without damage (see sketch A). The minimum trailer length (Fig. 2) may require
4. The cavity defined by A
embossment location and hole location shall be applied independent of each other.
additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2)
trude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical
restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm
maximum in the pocket (not applicable to vertical clearance.)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier
tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape
shall be pulled at a velocity of 300 ±10 mm/minute.
reels (with C-7280). Note that 13” reels are preferred.
Refer to EIA-556.
12 mm
12 mm
8 mm
8 mm
and
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Double
+0.004, -0.0)
(4 mm)
(8 mm)
Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13")
Single
+0.10 -0.0
12 mm
(0.059
8 mm
1.5
0
, B
0
, and K
(0.173)
(0.323)
ALUMINUM CHIP CAPACITORS
4.4
8.2
(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)
1.0 Kg Minimum.
TANTALUM, CERAMIC AND
1.75 ±0.10
0
The total peel strength of the cover tape from the carrier tape shall be:
shall be configured to surround the part with sufficient clearance such that the chip does not pro-
0.1 Newton to 1.0 Newton (10g to 100g)
0.1 Newton to 1.3 Newton (10g to 130g)
(0.039) (0.138 ±0.002)
(0.059) (0.217 ±0.002)
1.0
1.5
Packaging Information
4.0 ±0.10
3.5 ±0.05
5.5 ±0.05
Figure 1
(0.157 ±0.004) (0.984)
(0.315 ±0.004) (1.181)
2.0 ±0.05
4.0 ±0.10
8.0 ±0.10
(Metric will govern)
(0.024)
0.600
25.0
30.0
(0.098)
(0.181) (0.472 ±0.012)
(0.004)
0.100
2.5
4.6
(.315 ±0.012)
12.0 ±0.30
8.0 ±0.30
93