VBA40A-T04GN-Z SMC Corporation, VBA40A-T04GN-Z Datasheet - Page 23

• Manufacturer Part Number: VBA40A-T04GN-Z
• Description: BOOSTER REGULATOR, 1/2 NPTF, HANDLE OPERATED, PRESSURE GAUGE, PSI, SILENCER
• Manufacturer: SMC Corporation

Specifications of VBA40A-T04GN-Z

• Brand/series: VBA Series
• Flow Rate: 1900 SCFM
• Pressure Adjustment: Handle Operating
• Pressure Increase Ratio: Twice
• Pressure, Operating: 1 MPa
• Proof Pressure: 1.5 MPa
• Size, Port: 1⁄2 in.
• Temperature, Ambient: 2 to 50
• Thread Type: NPTF
• Lead Free Status / Rohs Status: RoHS Exempt Product

Back page 5
3. Draining
4. Exhaust
5. Maintenance
1. Operating pressure
2. Connection
Booster Regulator/Specific Product Precautions
• If this product is used with a large amount of drainage accumulated
• Exhausting time from E port may be longer for a booster regulator
• Life expectancy varies depending on the quality of air and the oper-
• When maintenance is required, confirm the model and serial num-
• Maintenance should be carried out according to the specified main-
• The list of replacement parts and kit part number are shown on
• Operate this product at or below the maximum operating
• Even when the tank alone is used, use a pressure switch or
• Connect a filter or a mist separator to the OUT side of the
• Using tank accessories, a VBA booster regulator can be
in the filter, mist separator, or the tank, the drainage could flow out,
leading to equipment malfunction. Therefore, drain the system
once a day. If it is equipped with an auto-drain, check its operation
once a day.
which is set to switch in longer hour intervals. This is not an abnor-
mal phenomenon.
ating conditions. As a symptom of the end of life expectancy, it can
be found by breathing all the time beneath the handle, or hearing
the exhausting sound from booster regulator in 10 to 20 second in-
tervals despite no air consumption in the outlet side. Conduct
maintenance earlier than scheduled in such cases.
ber of the booster regulator, and please contact SMC for mainte-
nance kit.
tenance procedure by individuals possessing enough knowledge
and experiences in maintaining pneumatic equipment.
page 6, and the figure shows the position of the parts.
pressure. If it is necessary, take appropriate safety meas-
ures to ensure that the maximum operating pressure is not
exceeded.
a safety valve to make sure that the maximum operating
pressure is not exceeded.
tank. Because the inner surface of the tank is untreated,
there is a possibility of dust flowing out to the outlet side.
connected directly in the combinations indicated below.
Caution
Warning
VBAT05A
VBAT05S
VBAT10A
VBAT10S
VBAT20A
VBAT20S
VBAT38A
VBAT38S
Air Tank/Specific Product Precautions
VBA111„-02
Series
Specific Product Precautions 3
Be sure to read this before handling.
Refer to back pages 1 and 2 for Safety Instructions and “Handling Precautions for SMC
Products” (M-E03-3) for Common Precautions.
b
b
—
—
Handling
Design
Booster regulator
VBA2„A
VBA
—
b
b
b
VBA4„A
b
b
—
—
1. Accessories
2. Installation
1. Inspection
2. Draining
• Consider the operating conditions and operate this product
• When using the air tank with a booster valve, refer to
• The accessories are secured by bands to the feet of the
• Tank should be installed away from people. It is dangerous
• Do not mount the air tank on a moving part or a place with
• When connecting a booster regulator with the tank, refer to
• To mount the air tank on a floor surface, use the four holes
• The use of pressure vessels could lead to an unexpected
• If this product is used with a large amount of drainage, the
within the specification range.
“Sizing” on page 5 or SMC Pneumatic System Energy Sav-
ing Program.
tank. Once removed, make sure not to lose them.
if the accumulated air inside the tank were to seep out.
vibration.
the operating manual first, which is provided with the air
tank before assembling.
to secure the tank with bolts or anchor bolts.
accident due to external damage or internal corrosion
caused by drainage. Therefore, make sure to check periodi-
cally for external damage, or the extent of internal corrosion
through the port hole. An ultrasonic thickness indicator may
also be used to check for any reduction in material thick-
ness.
drainage could flow out, leading to equipment malfunction
or corrosion inside the tank. Therefore, drain the system
once a day.
Caution
Caution
Warning
Air Tank/Specific Product Precautions
Maintenance
Mounting
Selection