VQ1100N-51 SMC Corporation, VQ1100N-51 Datasheet - Page 68

• Manufacturer Part Number: VQ1100N-51
• Description: SOLENOID VALVE, 5 PORT, BASE MOUNTED, PLUG IN TYPE, 24VDC, -COM
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of VQ1100N-51

• Brand/series: VQ Series
• Configuration: 2-Position Single
• Enclosure Rating: IP65
• Fluid Type: Air/Inert Gas
• Number Of Ports: 5
• Pressure, Operating: 0.7 MPa
• Primary Type: Solenoid Valve
• Temperature, Ambient: –10° to +50°C
• Valve Type: 5-Port Solenoid, Plug-In, Base Mounted with 2 Position Actuation, Rubber Seal, Negative Common
• Voltage, Coil: 24 VDC

Series
67
VQ1000: Manifold Optional Parts
DIN rail mounting bracket [-D/-D0/-D„]
VVQ1000-57A
It is used for mounting a manifold on a DIN rail.
1 set of DIN rail mounting bracket is used for 1 manifold
(2 DIN rail mounting brackets).
Direct EXH outlet with built-in silencer [-S]
This is a type with an exhaust port a top the manifold
end plate. The built-in silencer exhibits an excellent
noise suppression effect. (Noise reduction: 30 dB)
Dual flow fitting assembly
VVQ1000-52A-
This is a fitting to multiply the flow rate by combining the outputs of 2
valve stations. It is used for driving a large bore cylinder. This is a one-
touch fitting for a port size of ø8 or ø5/16”.
Silencer (For EXH port)
This silencer is to be inserted into the EXH port (one-
touch fittings) of the common exhaust type.
Regulator unit
VVQ1000-AR-1
The regulator controls the SUP pressure in a manifold.
Supply air from D-side SUP port is regulated. SUP port
on U-side is plugged.
When a regulator unit is mounted, the SUP port on the
U-side of the manifold will be plugged. A maximum of 3
units can be mounted on a manifold.
Specifications
Pressure gauge
G27-10-01
Pressure
control screw
Maximum operating pressure (MPa)
Set pressure range (MPa)
Ambient and fluid temp. ( C)
Fluid
Cracking pressure valve (MPa)
Structure
fold, suffix “D” to the end of the manifold part number.
fold, suffix “S” to the end of the manifold part number.
The port size for the manifold part number is “CM”.
Clearly indicate the dual flow fitting assembly part number and specify
the mounting station by means of the manifold specifications.
In dual flow fitting assembly, a special clip which is combined in one-
piece of 2 stations is attached as a holding clip.
L„) on the edge of manifold station, select a silencer,
AN203-KM8. A silencer (AN200-KM8) is interfered with
fittings.
When ordering this option incorporated with a mani-
When ordering this option incorporated with a mani-
When mounting elbow fitting assembly (VVQ1000-F-
D side
Note) A large quantity of drainage generated in
b Refer to back page 5 for maintenance.
the air source results in exhaust of air
together with drainage.
VQ1000
Regulator unit
C8
N9
C8 (SUP) port
ø8 one-touch fitting
Valve
Relieving type
0.05 to 0.7
5 to 50
0.02
0.8
Air
U side
SUP port on
U-side is plugged.
to be indicated alphabetically.
• How to Order
Indicate an option symbol “-G*” for the manifold no. and
be sure to specify the mounting position and number of
stations by means of the manifold specification sheet.
One unit is counted as one station and occupies a space
for three stations, therefore, pay attention to the manifold
size. The regulator valve unit, to which no wire is connec-
ted, valves can be mounted up to the standard max. num-
ber of stations of each kit.
How to Order Manifold
VV5Q11-14C6FUO-D G 2
Number of
manifold stations
Number of mounted
valves ··· 12 sets
Number of regulator
units ··· 2 sets
Others, option symbols:
+
R
X
P
+
31.5
SMC
DIN rail clamp screw
-
Counted as
one station.
With regulator unit
2
A
SMC
A
Number of
regulator units ··· 2 sets
B
4
Exhaust
Dimensions
• Pressure setting
Check the inlet pressure and then turn the pressure control screw to
set the outlet pressure. Turning the screw clockwise will increase the
outlet pressure while turning it counterclockwise decrease the pres-
sure. (Set the pressure by turning the screw in the increase direction.)
• Installation
Since some level of the actuator’s operational frequency may lead to a
sharp pressure change, pay attention to the pressure gauge durability.
VQ1000
Series
Caution
Mounting screws are attached.
Applicable
fitting size
ø
8
d
Flow Characteristics
Pressure
Characteristics
AN200-KM8
AN203-KM8
Model
Inlet pressure (MPa)
Conditions (Initial setting)
Flow rate (Nl/min)
59
32
A
78
51
L
Conditions:
Inlet pressure 0.7 MPa
Inlet pressure 0.7 MPa
Outlet pressure 0.2 MPa
22
16
Initial setting
value
D
Effective
(mm
area
20
14
2
)
reduction
Noise
(dB)
30
25