ITV2010-31N2L4 SMC Corporation, ITV2010-31N2L4 Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
ITV2010-31N2L4
Manufacturer Part Number
ITV2010-31N2L4
Description
Regulator; 1500L/min; .005-.1MPa range; 24VDC; 1/4NPT ports; 1-5VDC out
Manufacturer
SMC Corporation
Datasheet
1.ITV2050-31N2L4.pdf
(38 pages)
Specifications of ITV2010-31N2L4
Height
93 mm
Length
50 mm
Pressure, Operating
0.1 Mpa
Proof Pressure
0.1 MPa
Size, Port
1⁄4 "
Temperature, Ambient
0 to 50 °C
Thread Type
NPT
Accessory (Option)/Part No.
1. Connect the vacuum pump to the port, which is labeled “VAC”.
2. Pressure adjustment changes from “atmospheric pressure to
3. When adjusting the vacuum pressure, be careful not to block
4. Since this product is designed exclusively for use with negative
5. In cases where the vacuum pump being used has a relatively
6. The vacuum pressure response time after a change in the
7. If the electric power is shut off when in a control state, the
8. If the power for this product is cut off by a power failure, etc.
Be sure to read before handling. Refer to pages 14-21-3 to 14-21-4 for Safety Instructions and Common
Precautions.
Flat bracket
L-bracket
Cable
connector
vacuum pressure” when the input signal is increased, and
from “vacuum pressure to atmospheric pressure” when the
input signal is decreased.
the atmospheric pressure inlet port labeled “ATM”.
pressure, be careful not to apply positive pressure in error.
small capacity, or the piping has a small inside diameter, etc.,
large variations in the set pressure (the range of pressure
variation when changing from no flow to flow state) may
appear. In this situation, the vacuum pump or the piping, etc.
should be changed. In cases where it is not practical to
change the vacuum pump, install a capacity tank (volume
depending on the operating conditions) on the VAC side.
input signal is influenced by the internal volume on the setting
side (including piping). Since the capacity of the vacuum pump
also influences the response time, give careful consideration
to these points before operation.
pressure on the setting side will go into a holding condition.
However, this setting side pressure will be held only
temporarily and is not guaranteed. In addition, when
atmospheric pressure is desired, shut off the power after
reducing the set pressure, and then introduce atmospheric
pressure by using a vacuum release valve, etc.
when it is in a controlled state, the setting side pressure will be
held temporarily. Further, if operated without sealing the
setting side so that atmospheric air is sucked in, handle with
care as air will continue to be sucked in.
Caution
Description
Straight type
Right angle type
TM-4DSX3HG4
TM-4DLX3HG4
INI-398-0-6
P3020114
Part no.
4 - ø5.5
Dimensions
Flat bracket
Precautions
Handling
36
100
60
84
10. The setting side pressure cannot be completely released
11. This product is adjusted for each specification at the factory
12. The optional cable connector is a 4-wire type. When the
13. Use caution that the right angle cable does not rotate and is
14. Take the following steps to avoid malfunction due to noise.
15. Refer to the instruction manual included with the product for
9. If the VAC side pressure to this product is interrupted while
20
the power is still on, the internal solenoid valve will continue
to operate and may cause a humming noise. Since this may
shorten the life of the product, be sure to shut off the power
when the VAC side pressure is shut off.
from this product in the range below –1.3 kPa. In cases
where the pressure needs to be reduced completely to 0 kPa,
install a 3 port valve, etc. on the setting side to discharge the
residual pressure.
before shipment. Avoid careless disassembly or removal of
parts, as this can cause failure.
monitor output (analog output, switch output) is not being
used, keep it from touching the other wires, as this can cause
malfunction.
limited to only one entry direction.
1)
2) Install this product so that it will not be effected by noise,
3) Make sure to take protective measures against load surge
details on its handling.
4 - ø7
installing a line filter, etc. in the AC power line.
keeping the product and its wiring away from strong
electric field sources such as motors and power lines.
for an induction load (solenoid valves, relays, etc.).
Eliminate power supply noise during operation by
L-bracket
(10)
(7)
7
36
50
30
36
50
4 - ø5.5
14-8-33
2.3
F.R.L.
AV
AU
AF
AR
IR
VEX
AMR
ITV
IC
VBA
VE
VY1
G
PPA
AL