CHEMICALS
“Instant bonding” cyanoacrylate adhesives cure in seconds, do not depend on evaporation of solvents and require no clamping. They
are colorless and moisture resistant. They are ideal for bonding metals, plastics, rubber, glass and ceramics to each other or to dissimi-
lar
sives are economical, as only a drop is required. The best type should be determined by experimentation. Use them to repair broken plastic
cabinets and other plastic items, attaching nameplates and rubber feet to panels and chassis, cementing broken ceramic glass and rubber
items, repairing jewelry, etc. Porous surfaces may be bonded with Gelweld No. 19-0117. The average setting time is between 10 and 100
seconds, after which the cemented articles can be handled. These adhesives may even be used to bond surfaces which are normally difficult
to cement, such as teflon, polyethylene, vinyl, silicone rubber and glass.
materials. Bonding strength up to several thousand psi is possible making them among the strongest adhesives available. These adhe-
GC Electronic Grade Self Leveling
Potting Silicone Sealant
Electronic Grade Self Leveling Silicone is a one-compo-
nent, RTV (room temperature vulcanizing) product
that uses new cross-linking mechanism as a cure
method. No acetic or other corrosive by-products
are
curing process. It can be used in corrosion sensitive
electrical or electronic equipment with no adverse
effect and cures at room temperature.
Temperature Range
(after cure):
Dielectric Strength:
Thermal Expansion
Coefficient:
Volume Resistivity:
Part No. 19-160
GC Super Adhesive
Ethyl Cyanoacrylate Adhesive
Forms strong, lasting bonds in seconds between
either similar or dissimilar materials metal,
porcelain,
hardwoods, and other non-porous materials with
smooth, close-fitting surfaces. The bond resists
softening at temperatures up to 320°F (160°C).
Your most versatile adhesive for bonding,
attaching, fixturing. Cures to a strength of 5000
psi; because it is solvent-free, there is no
shrinking during curing and no solvent fumes.
Fills gaps to .003".
Meets Mil. Spec. MIL-A-46050C Type I Class 2
Part No. 10-128
GR-R-RIP
World famous Ethyl Cyanoacrylate rapid
bonding adhesive in gravity fed bottle.
Bond strength not affected by temperatures
from -60°C to 85°C (-76°F to 185°F).
Part No. 19-115
generated
CYANOACRYLATE ADHESIVES & DEBONDERS
plastic,
1 fl. oz. Bottle
10.2 fl. oz. Caulk Tube, Clear
0.106 fl. oz. Bottle
452 V/mil (173 KV/cm)
-57
9 x 10
0˚C to 100˚C (32˚F to 212˚F)
>2.19 x 10 15 Ohm/cm
(-70˚F to + 400˚F)
All quantities are single; BU’s are packages of 10 Unless otherwise noted.
º
C to +204
glass,
4
1/K
EPOXY CEMENTS (Cont.)
during
.
º
C
most
rubbers,
the
Part A
Part B
GC Super Glue Regular Formula
Ethyl Cyanoacrylate Adhesive
Medium viscosity formula for efficient wicking
action, faster curing time. Excellent for bonding
any combination of plastic, rubber or metal
parts. This grade is ideal for small or fine work on
non-porous, smooth surfaces. It fills gaps of .003-
.005”. Highly resistant to acid, alkali, alkali
water, solvents and fungus. Non-toxic.
Meets Mil. spec. MIL-A-46050B Type 1 Class 2.
Part No. 10-120
GELWELD
GEL Cyanoacrylate Adhesive
Ethyl Cyanoacrylate super strength adhesive
in a “gel’’ form – will not drip or run. Fills
gaps well.
Part No. 19-117
Thermally Conductive Potting
Epoxy and Adhesive
This potting Epoxy and adhesive is a highly
filled medium
resin formulated for application requiring a
high degree of thermal conductivity. Mix
ratio 1:1. It contains abrasive aluminum
oxide filler which can introduce wear
considerations. Cure is normally achieved at
room temperature, although an elevated cure
schedule can be used to reach final
properties quickly.
Temperature Range:
Dielectric Strength:
Thermal Conductivity: 7.34 (Btu * in/ft 2 hr ˚F)
Thermal Expansion
Coefficient:
Volume Resistivity:
Part No. 19-161
0.075 fl. oz. Tube
0.101 fl.oz. Tube
2-4 oz. Containers
(40˚F to 300˚F)
-40˚C to 150˚C
430 V/mil
44 (x 10 6 ˚C)
2.14 x 10 12 Ohm/cm
viscosity black casting
51
