LD6A-3KQB-RYG IDEC Corporation, LD6A-3KQB-RYG Datasheet - Page 11

• Manufacturer Part Number: LD6A-3KQB-RYG
• Description: Light Tower Steady 24 V AC/DC Pole Mnt W/ L Bracket; Blk 3 Tier; Lens R/Y/G IP23
• Manufacturer: IDEC Corporation
• Type: Steadyr

Specifications of LD6A-3KQB-RYG

• Brand/series: IDEC LD6A
• Color: Red/Yellow/Green
• Enclosure Rating: IP23
• Life: 30,000 hrs
• Mounting Style: Red, Yellow, Green
• Mounting Type: Pole
• Primary Type: Tower
• Voltage, Operating: 24 VDC
• Voltage, Supply: 24 VAC/VDC
• Weight: 720 g
• Operating Voltage: 24 VAC/DC
• Degree Of Protection: IP23
• Lead Free Status / Rohs Status: RoHS Compliant part

Safety Precautions
•
•
•
•
•
•
Instructions
Mounting
•
•
•
Frame Mounting
1.
2.
Note: See table below for typical examples of frames and nuts. Consult the
Examples of recommended frames and frame nuts
*The mounting bracket for the housing is 40 mm.
When using a frame mount type, be sure to
use flexible conduit, otherwise the waterproof
seal will be compromised.
Refer to the “Example of Flexible Conduit”
shown on the right.
Example of Flexible Conduit
Wall Mounting
1.
Conduit Port Size
Gland
Conduit
Manufacturer
Turn off the power to the LD6A before mounting, removing, wiring or
assembling the LED module. Make sure the wiring is done correctly otherwise
electrical shock or fire may result.
Mount the LD6A on a solid surface not subject to vibrations.
Do not mount the LD6A upside-down or horizontally.
Do not leave the LD6A without a cap or unassembled.
Install the supplied gasket, otherwise the waterproof seal will be compromised.
Do not apply any chemicals that may corrode the plastic materials.
See drawing below regarding the mounting of the LD6A.
For panel cut-out dimensions, see pages 9 and 10.
Postion the LD6A to make sure the alarm sound is the loudest. (Steady/
flashing/alarm type)
Frame Size
30 mm*
40 mm
Insert two nuts in the frame, and attach the bracket using two M5 screws.
Recommended tightening torque: 2.6 to 2.7 N·m
Mount the LD6A to the bracket using four M4 screws.
Recommended tightening torque: 1.6 to 1.7 N·m
Make four tapped holes in the mounting panel and mount the bracket
and gasket using four screws (M4 x 20).
Recommended tightening torque: 1.6 to 1.7 N·m
manufacturer of the frame for the installation method of the frame nut.
➁
M4 Screw, Spring Washer, Plain Washer
➀
Frame
SFF-302
SFF-402
Spring Washer
Plain Washer
M5 Screw
M20
AL16/M20/A/BL
PAFS16BL
Adaptaflex
Bracket
Frame Nut
SFB-001
SFB-4B5
SFB-101
SFB-008
SFB-4A5
SFB-108
Frame Nut (Note)
Frame (Note)
Conduit port
(M20×P1.5)
Conduit
Gland
Manufacturer
SUS
Corporation
(Japan)
•
•
2.
Direct Mounting
Recommended tightening torque:
2.6 to 2.7 N·m
Pole Mounting (with base)
The pole mount type can be installed in four ways. The recommended mounting
method (pattern A from page 9 or 10) is described below.
Recommended tightening torque: 2.6 to 2.7 N·m (M5 screw)
Pole Mounting (with L-shaped bracket)
11
21
1. Using L-shaped bracket
The parts marked with * are not supplied and should be provided by the user.
Hexagonal
nut
(M22)
Hexagonal
bolt∗
(M10)
If the LD6A is subjected to strong vibrations, the hexagon socket screw may
become loose. Take measures to prevent loosening. (See the figure below.)
Do not loosen any screws if the tightening torque is not specified.
Mount the LD6A to the bracket using four screws (M4 x 8).
Recommended tightening torque: 1.6 to 1.7 N·m
Using L-shaped bracket
Recommended tightening torque: 10 to 11 N·m (M10)
Recommended tightening torque: 25 to 26 N·m (M22)
Not using L-shaped bracket
Remove the bushing, hexagonal nut (M22), plain washer, and L-shaped
bracket from the LD6A and install in the following order: plain washer,
hexagonal nut (M22), and bushing.
Recommended tightening torque: 25 to 26 N·m (M22)
M5 Screw
O-ring
Pole Stand
Gasket
Panel
Plain Washer
Spring Washer
Nut
➁
M4 Screw (8 mm), Spring Washer, Plain Washer
➀
（recommended tightening torque:
1.1 to1.2 N ・ m）
4-M5
Mounting
Hole
2-M4 holes for hexagon socket
set screws
Panel
Plain washer∗
Hexagonal
nut∗
(M10)
Spring washer∗
M4 Screw (20 mm)
Spring Washer
Plain Washer
Pole Stand
2. Not using L-shaped bracket
Bracket
Gasket
4-M5 Mounting Hole
(recommended)
4-M4 Mounting Hole
3-M4 Mounting Hole
M5 Screw
Spring Washer
Plain Washer
O-ring
Base
Gasket
Nut
Panel
Nut
Plain washer
Hexagonal nut
(M22)
Bushing
11