HEDS-5140-A05 Avago Technologies US Inc., HEDS-5140-A05 Datasheet
HEDS-5140-A05
Specifications of HEDS-5140-A05
Related parts for HEDS-5140-A05
HEDS-5140-A05 Summary of contents
Page 1
... Codewheels available in glass, film, and metal • Available in two standard diameters • Cost effective • Resolutions from 96 CPR to 2048 CPR • For use with HEDS-90XX/91XX Series two and three channel encoders • Lead free Also See: • HEDS-9000/HEDS-9100 Encoder Module Data Sheet • ...
Page 2
... Radial Play Note: Avago Encoder Modules are guaranteed to 100 kHz, but can operate at higher frequencies. See Encoder Module Data Sheet for specifications and output load recommendations. *HEDM-6140 is guaranteed to 100 kHz with the HEDS-9040 #T00 module. 2 rugged, but do not offer higher resolution capabilities. Film ...
Page 3
... Encoding Characteristics Encoding characteristics over recommended operating range and recommended mounting tolerances unless otherwise Part Number Description HEDS-51XX Cycle Error Position Error HEDS-61XX Cycle Error Position Error HEDM-512X Cycle Error Position Error HEDM-61XX Cycle Error Position Error HEDG-512X Cycle Error Position Error ...
Page 4
... Mounting Rotary Encoders with Codewheels There are two orientations for mounting the Avago encoder module and Avago codewheel. Figure 1a shows mounting the module with side A as the ;; ;; mounting plane. Figure 1b shows mounting the module with side B IMAGE SIDE OF CODEWHEEL Figure 1a. ...
Page 5
... CODEWHEEL MODULE SIDE B Figure 3. Alignment Tool is Placed over Shaft and onto Codewheel Hub. Alignment Tool Pins Mate with Aligning Recesses on Module. 4. Slide the HEDS-8905 or HEDS- 8906 centering tool over codewheel hub and onto module as shown in Figure 3. The pins of the alignment tool ...
Page 6
... INDEX PULSE REFERENCE MARKER INDEX PULSE 130° ± 5° POSITION TYPICAL R = 11.00 mm (0.433 in.) OP DIMENSIONS IN MM (INCHES) Figure 6. HEDS-5140 Codewheel Used with HEDS-9140. 6 5.94 (0.234) MAX. MOUNTING BOSS – NOT USED & 1/4" I.D. HUBS # 2-56 SETSCREW USE 0.035" HEX WRENCH ...
Page 7
... INDEX PULSE REFERENCE MARKER INDEX PULSE 130° POSITION TYPICAL R = 23.36 mm (0.920 in.) OP DIMENSIONS IN MM (INCHES) Figure 7. HEDS-6140 Codewheel Used with HEDS-9040 0.18 (0.007) 25.56 DIA. (1.006) MAX. ARTWORK SIDE ARTWORK SIDE (HEDM-5121) (HEDM-5120) Figure 8. HEDM-5120 Codewheel/HEDM-5121 Codewheel 2-56 SETSCREW USE 0.035" HEX WRENCH 50 ...
Page 8
ARTWORK SIDE 25.56 DIA. ARTWORK SIDE (HEDG-5120) (1.006) MAX. (HEDG-5121) DIMENSIONS IN mm (INCHES) Figure 10. HEDG-5120 Codewheel/HEDG-5121 Codewheel 50.48 DIA. (1.987) MAX. SETSCREW INDEX PULSE 130° POSITION TYPICAL ARTWORK SIDE Figure 12. HEDM-6140 ...
Page 9
... Ordering Information Encoder Modules, Codewheel and Assembly Tools Metal Codewheels 0 HEDS-9100 Option 0 modules HEDS-5120 HEDS-9140 Option 0 modules HEDS-5140 HEDS-5120 Option codewheels Resolution Shaft Diameter (Cycles/Rev CPR C - 100 CPR D - 192 CPR E - 200 CPR F - 256 CPR G - 360 CPR H - 400 CPR A - 500 CPR I - 512 CPR ...
Page 10
... Ordering Information (Cont’d.) 0 HEDS-9000 Option 0 modules HEDS-6100 HEDS-9040 Option 0 0 modules HEDS-6140 Note: 1. For the lower resolution, two channel encoders, (11 mm are not necessary, but sometimes helpful in an assembly process. 10 HEDS-6100 Option codewheels Resolution Shaft Diameter (Cycles/Rev 500 CPR B - 1000 CPR ...
Page 11
... Option Artwork Orientation Shaft Diameter 0 - Artwork on hub 06 - 1/4 in. side (use when 08 - 3/8 in. module side down Artwork opposite hub side (use when module side A is down Assembly Tools Centering Gap-Setting HEDS- HEDS- 8905 Assembly Tools Centering Gap-Setting HEDS- HEDS- 8906 * 8901 8906 ...
Page 12
... Option Artwork Orientation Shaft Diameter 0 - Artwork on hub 06 - 1/4 in. side (use when module side B is down Artwork opposite hub side (use when module side A is down Assembly Tools Centering Gap-Setting HEDS- HEDS- 8906 8906 Assembly Tools Centering Gap-Setting HEDS- HEDS- 8905 8932 * ...
Page 13
... Ordering Information (Cont’d.) HEDS-9000 HEDG-612 modules codewheels Option 0 0 Option Resolution (Cycles/Rev 2000 CPR U - 2048 CPR HEDG-6120 Rop = 23.36 mm, 2 Channels Shaft Diameter Assembly Tools Centering Gap-Setting HEDS- HEDS- 8906 8932 ...
Page 14
For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © ...