RWM0410R120JR15E1 Spectrol / Sfernice / Vishay, RWM0410R120JR15E1 Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
RWM0410R120JR15E1
Manufacturer Part Number
RWM0410R120JR15E1
Description
Resistor; Wirewound; Res 0.12 Ohms; Pwr-Rtg 3 W; Tol 5%; Axial; Vitreous Enamel
Manufacturer
Spectrol / Sfernice / Vishay
Datasheet
1.RWM04103300JR15E1.pdf
(4 pages)
Specifications of RWM0410R120JR15E1
Material, Element
Wirewound
Package Type
Vitreous Enamel
Power, Rating
3 W
Resistance
0.12 Ohms
Termination
Sn/Ag/Cu
Tolerance
±5 %
Lead Free Status / Rohs Status
RoHS Compliant part
OVERLOAD
Heavy overloads can be endured in the form of short pulses
< 0.1 s. Particular requirements should be submitted to
Vishay Sfernice, specifying peak voltage, cycle and
environmental conditions.
RECOMMENDATIONS FOR USE
Since these components are high dissipation power
resistors, customers are advised to use a high melting point
solder.
For low ohmic values, the measurement becomes critical
and the connecting wires resistance is to be included. The
value is measured at 5 mm from the resistor body.
Document Number: 50008
Revision: 11-Jun-08
PERFORMANCE
TESTS
Short Time Overload
Temperature Cycling
Humidity (Steady State)
Terminal Strength
Load Life
ELECTRICAL SPECIFICATIONS
Tolerance
Temperature Coefficient + 75 ppm/°C typical
Dielectric Withstanding Voltage NF EN 140000
Inductance
CECC 40201 - EN 140-201
40 °C Ambient - R.H. 95 %
Enamelled Wirewound Power Resistors
2 full rotations of 180°
2 successive bending
10 Pr during 10 s
Tensile test: 20 N
- 55 °C + 200 °C
CONDITIONS
25 °C ambient
25 °C ambient
For technical questions, contact: sfer@vishay.com
1000 h at Pr
90/30 cycle
56 days
Standard
On request
Axial Leads
Group Mounting
In a still atmosphere, a distance between axes equal to five
times the resistor’s diameter is recommended.
Cabinet Mounting
• Unventilated box: dissipation should be reduced (see
dimensional drawing).
• Forced ventilation: if conditions are appropriate, dissipation
may be doubled or even trebled.
• In any case: the surface temperature at the hottest point
should not exceed 450 °C.
These aspects should be considered by the end user.
REQUIREMENTS
± (1 % + 0.05 Ω)
± (1 % + 0.05 Ω)
± (2 % + 0.1 Ω)
± (5 % + 0.1 Ω)
± (5 % + 0.1 Ω)
non inductive (Ayrton-Perry) winding available
500 V
± 1 % and ± 2 %
RMS
± 5 %
- 1 min - 10 mA
Vishay Sfernice
TYPICAL DRIFTS
± (0.5 % + 0.05 Ω)
± (0.5 % + 0.05 Ω)
± (0.5 % + 0.05 Ω)
± (0.1 % + 0.05 Ω)
± (1.5 % + 0.05 Ω)
www.vishay.com
RWM
39