DS14C88N/NOPB National Semiconductor, DS14C88N/NOPB Datasheet - Page 3

• Manufacturer Part Number: DS14C88N/NOPB
• Description: IC LINE DRIVER QUAD CMOS 14-DIP
• Manufacturer: National Semiconductor
• Type: Line Driver, Transmitterr

Specifications of DS14C88N/NOPB

• Number Of Drivers/receivers: 4/0
• Protocol: RS232
• Voltage - Supply: 4.5 V ~ 12.6 V
• Mounting Type: Through Hole
• Package / Case: 14-DIP (0.300", 7.62mm)
• Interface Circuit Standard 1: EIA/TIA-232-D/V.28
• Number Of Receivers: Not Required
• Number Of Transmitters: 4
• Number Of Transceivers: Not Required
• Data Transmission Topology: Point-to-Point
• Receiver Signal Type: Not Required
• Transmitter Signal Type: Single-Ended
• Single Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (typ): ±5/±9/±12V
• Dual Supply Voltage (min): ±4.5V
• Dual Supply Voltage (max): ±12.6V
• Supply Current: 0.5mA
• Power Supply Requirement: Dual
• Operating Temp Range: 0C to 75C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 14
• Package Type: MDIP
• Device Type: Line Driver
• No. Of Drivers: 4
• Driver Case Style: DIP
• No. Of Pins: 14
• Operating Temperature Range: 0°C To +75°C
• Msl: MSL 1 - Unlimited
• Filter Terminals: Through Hole
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *DS14C88N; *DS14C88N/NOPB; DS14C88N

t
t
t
t
tsk
S
PLH
PHL
r
f
R
Switching Characteristics
Over Recommended Operating Conditions, unless otheriwse specified (Figures 2, 3)
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation.
Note 2: Derate N Package 12.1 mW/˚C, and M Package 8.5 mW/˚C above +25˚C.
Note 3: I
Note 4: Power supply (V
Note 5: AC input test waveforms for test purposes: t
Note 6: Input rise and rall times must not exceed 5 µs.
Note 7: The output slew rate, rise time, and fall time are measured from the +3.0V to the −3.0V level on the output waveform.
Note 8: C
Note 9: ESD Rating (HBM, 1.5 kΩ, 100 pF) ≥ 1.0 kV.
Parameter Measure Information
Symbol
OS+
L
include jig and probe capacitances.
and I
Propagation Delay
Low to High
Propagation Delay
High to Low
Rise Time (Note 7)
Fall Time (Note 7)
Typical Propagation
Delay Skew
Output Slew Rate
(Note 7)
OS−
values are for one output at a time. If more than one output is shorted simultaneously, the device dissipation may be exceeded.
+
, V
Parameter
−
) and GND pins are connected to ground for the Output Resistance Test (R
FIGURE 1. Output Resistance Test Circuit (Power-Off)
r
FIGURE 2. Driver Load Circuit (Note 8)
= t
(Notes 5, 6)
V
V
V
V
V
V
V
V
V
R
C
f
+
+
+
+
+
+
+
+
+
≤ 20 ns, V
L
L
= +4.5V, V
= +9.0V, V
= +12V, V
= +4.5V, V
= +9.0V, V
= +12V, V
= +4.5V, V
= +9.0V, V
= +12V, V
= 3 kΩ to 7 kΩ
= 15 pF to 2500 pF
Conditions
IH
= 2V, V
−
−
−
−
−
−
−
−
−
= −12V
= −12V
= −12V
= −4.5V
= −9.0V
= −4.5V
= −9.0V
= −4.5V
= −9.0V
IL
3
= 0.8V (0.6V at V
+
01110503
= 4.5V, V
Min
0.2
0.2
O
).
−
= −4.5V)
1.35
Typ
250
200
150
1.5
1.2
1.2
1.5
1.3
1.0
1.0
01110502
Max
6.0
5.0
4.0
6.0
5.0
4.0
30
www.national.com
Units
V/µs
µs
µs
µs
µs
µs
µs
µs
µs
ns
ns
ns