V100 Bogen Communications, Inc., V100 Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
V100
Manufacturer Part Number
V100
Description
Amplifier; 140 W @ 1kHz (Typ.); 70 dB (Aux, Tel), 60 dB (Mic); 0.4 V; Screw
Manufacturer
Bogen Communications, Inc.
Datasheet
1.V250.pdf
(2 pages)
Specifications of V100
Controls
100 Hz (+⁄- 10 dB Min.) Bass, 10 kHz (+⁄- 10 dB Min.) Treble
Dimensions
16-1⁄2 in. W x 3-1⁄2 in. H x 12 in. D
Frequency Response
45 to 20 kHz (Transformer), 20 to 20 kHz (Direct)
Hum And Noise
70 dB (Aux, Tel), 60 dB (Mic)
Impedance, Output
8 Ohms Transformer Coupled, 4 Ohms Direct Coupled
Mounting Type
Rack Mount
Power Output
140 W @ 1kHz (Typ.)
Sensitivity
0.4 V
Termination
Screw
Weight, Shipping
40 lbs.
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
V1000
Manufacturer:
COOLAUD
Quantity:
20 000
Company:
Part Number:
V1000LA160BP
Manufacturer:
LITTELFUSE
Quantity:
32 000
Company:
Part Number:
V1000LA80AP
Manufacturer:
LITTELFUSE
Quantity:
32 000
Company:
Part Number:
V1000N6
Manufacturer:
LUCENT
Quantity:
1 831
Part Number:
V100105
Manufacturer:
CEPESAMZD
Quantity:
20 000
Part Number:
V100370HR016BA00TR
Manufacturer:
SUYIN/实盈
Quantity:
20 000
Company:
Part Number:
V100ZA3P
Manufacturer:
LITTELFU
Quantity:
1 500
Company:
Part Number:
V100ZA4
Manufacturer:
HARRIS
Quantity:
2 485
Power Output (RMS): V35
Rated:
Typical @ 1 kHz:*
Frequency Response
Transformer:
Direct:
Distortion
Transformer:
Direct:
Signal-to-Noise
Fundamental:
With Aux Module:
With Mic Module:
With Tel Module:
Tone Controls
Bass Frequency:
Treble Frequency:
Low Cut Frequency:
Sensitivity
Output Regulation:
*
**
†
Architect and
Specifications
Specifications
Typical, @1 kHz/0.1% THD/4Ω)
THD+N, Maximum, Full bandwidth @ FRP
Referenced to FRP output level, 20-20 kHz bandwidth limited.
Technical
Engineer
†
The amplifier shall be a Bogen Power Vector Amplifier,
Model V35,V60,V100,V150 or V250. The amplifier shall be
compatible with both high- (70/25V) and low- (4/8-ohm)
impedance speakers, with the capability of 35, 60, 100, 150,
or 250 watts, respectively.
The amplifier shall provide 8 module bays for plug-in input
modules with two of the bays also capable of handling plug-
in signal processing output modules.There shall be 4 levels
of priority between modules.
Each of the 8 module bays shall have an associated inde-
pendent volume control. Each independent volume control
shall have a signal/clip LED to indicate if a clipping condition
is occuring. Each amplifier shall also include bass and treble
controls, as well as a motorized master volume control,
which can be remotely operated using the RVCP accesso-
ry (sold separately).
Two screw terminals shall be provided for invoking a mas-
ter mute function that will interrupt all audio from the
mixer section of the Power Vector amplifier.
An 11-segment LED output level meter will register either
the average or peak level of the amplifier’s output level,
determined by an Average/Peak switch. Each Power Vector
amplifier shall have a Tone Control Bypass switch and a
Low-Cut Filter switch located on the rear of the amplifier
in module bay 6.
35W 60W
45W 85W
45-20 kHz; 0/-2 dB
20-20 kHz; 0/-1 dB
0.5%**
0.1%** (.05 typical @ 1 kHz)
-94 dB
-70 dB
-60 dB
-70 dB
100 Hz (+/- 10 dB minimum)
10 kHz (+/- 10 dB minimum)
125 Hz @ -6 dB/octave
0.4V (at module bay connector)
2 dB or better, no load to full load
V60
100W 150W 250W
140W 200W 340W
V100
V150
V250
Output Impedance
Transformer-Coupled:
Direct Coupled:
Inserts
Insert "OUT" Level:
Insert "OUT" Impedance:
Insert "IN" Sensitivity:
Insert "IN" Impedance:
Pre-EQ Output
Output Level:
Output Impedance:
AC Power Receptacle:
AC Voltage:
AC Current:
Product Weight (lb.):
Dimensions:
A lockable switch will permit the selection of transformer-
coupled output or direct output for speaker runs. Master
mute and remote volume control functions are controlled
using a screw terminal.
Signal processing insert jacks (RCA connectors) will allow
external equipment to be inserted between the pre-amp
output and the power amp input.
Each model will have a Pre-EQ unbalanced (RCA jack)
buffer output whose signal is post all volume controls, tone
controls, and output module signal processing, but before
(pre-EQ) any external signal processing equipment con-
nected to the Signal Processing Insert jacks.
Each amplifier will include a 500W maximum, unswitched
AC power receptacle.
The amplifier shall fit into a 19" rack and fit in two rack
spaces. It shall allow the attachment of feet for tabletop
placement. Each model shall measure 17" W x 3-1/2" H
x 13-1/2" D.The V35 shall weigh 24 lb., the V60 - 28 lb., the
V100 - 32 lb., the V150 - 35 lb., and the V250 - 40 lb.
50 Spring Street, Ramsey, New Jersey 07446, U.S.A.
201-934-8500 FAX: 201-934-9832
Web Site: www.bogen.com
70V, 25V, 8 ohms (bal or unbal)
4 ohms
1VRMS (@FRP)
50 ohms maximum
1VRMS
10k ohms minimum
4VRMS (@FRP)
50 ohms maximum
500 watts maximum power, unswitched
120V AC, 60Hz
16-1/2" W x 3-1/2" H x 12" D
(all models)
0.6A
V35
V35
24
1.3A
V60
V60
28
V100 V150 V250
V100 V150 V250
2.0A
32
3.5A
35
5.5A
40