CW2900 Chemtronics, CW2900 Datasheet - Page 2

• Manufacturer Part Number: CW2900
• Description: Flex Conductive pen, micro tip, 9 g
• Manufacturer: Chemtronics
• Type: Conductiver

Specifications of CW2900

• Dispensing Method: Pen
• Primary Type: Coating
• Lead Free Status / Rohs Status: RoHS Compliant part Hazardous Materials

USAGE INSTRUCTIONS
Read MSDS carefully prior to use.
Cleaning:
Chemtronics Electro-Wash
in order to remove any surface contamination which
may prevent adequate material contact.
Mixing: Although this system has been formulated
to resist hard-packing, it should be shaken
vigorously for 30 seconds to insure the proper
dispersion of the silver flakes. If pen has been
allowed to sit idle for a long period of time, the
mixing ball may seize in the barrel. To free the ball
use force to tap the barrel end of the pen until the
ball begins to move inside the pen.
Application:
through the CircuitWorks
Squeezing the pen body while pressing down on the
surface will allow the material to flow through the
tip, enabling the trace to be drawn. Practice with
the pen before attempting detail work.
Thinning: The conductive ink has been optimized
for the CircuitWorks
thinning is not normally necessary. However, a
small amount of Butyl Acetate may be added with
thorough mixing to make slight adjustments for
ease of application for other dispensing systems.
Clean-up/Removal: The conductive ink may be
cleaned or removed using a strong organic solvent
such as acetone or Chemtronics
Two-Step (ES125a).
Curing: Dries tack-free in about 5 minutes at room
temperature.
within 15 minutes. Full conductivity after 24 hours
at room temperature. Heat cure for 15 minutes at 80
to 90°C for maximum conductivity, durability and
chemical resistance.
TECHNICAL & APPLICATION
ASSISTANCE
ITW Chemtronics
answer your technical and application related
questions. The toll free number is:
1-800-TECH-401.
For best adhesion, clean board with
The conductive ink is dispensed
Achieves electrical conductivity
®
provides a technical hotline to
®
Flex Conductive Pen and
®
®
Flex Conductive Pen.
PX Cleaner Degreaser
®
Electro-Wash
®
DISTRIBUTED BY:
AVAILABILITY
CW2900
Ozone depletion potential (ODP) is determined in accordance with the
Montreal
Hydrochlorofluorocarbons (HCFCs) are regulated under the Montreal
Protocol as Class II ozone depleting substances. Volatile Organic Compound
(VOC) information is calculated on a weight basis using the VOC definition
of California Air Resources Board (CARB) Consumer Product Regulations,
South Coast Air Quality Management District (SCAQMD) Rule 102 and the
Federal definition published in 40 CFR 51.100(s). Hydrofluorocarbons
(HFCs) are not currently regulated.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
CHEMTRONICS
of the data and assumes no liability in connection
with damages incurred while using it.
Chemtronics®, Electro-Wash® and CircuitWorks® are
registered trademarks of ITW Chemtronics.
reserved.
Chemtronics. All rights reserved. All other trademarks herein
are trademarks or registered trademarks of their respective
owners.
MANUFACTURED BY:
ITW CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888
ODP
HCFC
ENVIRONMENTAL IMPACT DATA
Protocol
ControlWipes™ is a trademark of ITW
and
®
None
None
does not guarantee the accuracy
U.S.
®
Clean
8.5 g (0.3 oz.) pen
VOC
HFC
Air
REV. E (01/08)
Act
None
Yes
All rights
of
ITW
1990.