MAX3098EBCEE+ Maxim Integrated Products, MAX3098EBCEE+ Datasheet - Page 10
![IC RS485/422 RX 32MBPS 16-QSOP](/photos/6/61/66127/175-16-qsop_sml.jpg)
MAX3098EBCEE+
Manufacturer Part Number
MAX3098EBCEE+
Description
IC RS485/422 RX 32MBPS 16-QSOP
Manufacturer
Maxim Integrated Products
Type
Receiverr
Datasheet
1.MAX3097ECSE.pdf
(16 pages)
Specifications of MAX3098EBCEE+
Number Of Drivers/receivers
0/3
Protocol
RS422, RS485
Voltage - Supply
3 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
16-QSOP
Data Rate
32000 Kbps
Propagation Delay Time Ns
75 ns to 85 ns
Operating Supply Voltage
3.3 V to 5.5 V
Supply Current
3.1 mA
Operating Temperature Range
0 C to + 70 C
Input Voltage
3.3 V to 5.5 V
Maximum Power Dissipation
697 mW
Mounting Style
SMD/SMT
Output Current
+/- 105 mA
Output Voltage
- 0.3 V to + 5.3 V
Product
RS-422/RS-485 Combination
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
±15kV ESD-Protected, 32Mbps, 3V/5V,
Triple RS-422/RS-485 Receivers with Fault Detection
___________Applications Information
The MAX3097E/MAX3098E are triple RS-485 receivers
designed for shaft encoder receiver applications. A
shaft encoder is an electromechanical transducer that
converts mechanical rotary motion into three RS-485
differential signals. Two signals, A (A and A) and B (B
and B) provide incremental pulses as the shaft turns,
while the index signal, Z (Z and Z) occurs only once
per revolution to allow synchronization of the shaft to a
known position. Digital signal processing (DSP) tech-
niques are used to count the pulses and provide feed-
back of both shaft position and shaft velocity for a
stable positioning system.
Shaft encoders typically transmit RS-485 signals over
twisted-pair cables since the signal often has to travel
across a noisy electrical environment (Figure 7).
Signal integrity from the shaft encoder to the DSP is
essential for reliable system operation. Degraded sig-
nals could cause problems ranging from simple mis-
counts to loss of position. In an industrial environment,
many problems can occur within the three twisted
pairs. The MAX3097E/MAX3098E can detect various
types of common faults, including a low-input-level sig-
nal, open-circuit wires, short-circuit wires, and an input
signal outside the common-mode input voltage range
of the receiver.
In Figure 8, if wires A and A are shorted together, then A
and A will be at the same potential, so the difference in
the voltage between the two will be approximately 0. This
causes fault A to trigger since the difference between A -
A is less than the differential fault threshold.
Detecting an open-circuit condition is similar to detect-
ing a short-circuit condition and relies on the terminat-
ing resistor being across A and A. For example, if the
wire drops out of the A terminal, A pulls A through the
terminating resistor to look like the same signal. In this
condition, V
10
Using the MAX3097E/MAX3098E as Shaft
______________________________________________________________________________________
Detecting Open-Circuit Conditions
ID
is approximately 0 and a fault occurs.
Detecting Short Circuits
Encoder Receivers
Detecting Faults
Figure 6a. IEC 1000-4-2 ESD Test Model
Figure 6b. IEC 1000-4-2 ESD Generator Current Waveform
Figure 7. Typical Shaft Encoder Output
VOLTAGE
SOURCE
t
r
HIGH-
= 0.7ns to 1ns
DC
A
A
B
B
Z
Z
CHARGE-CURRENT
100%
LIMIT RESISTOR
90%
10%
50MΩ to 100MΩ
I
R
C
150pF
C s
30ns
STORAGE
CAPACITOR
RESISTANCE
DISCHARGE
330Ω
R
60ns
D
DEVICE
UNDER
TEST
t