SUBMINIATURE
(NEV: Radial Lead, NEH: Axial Leads)
The NEV and NEH series subminiature aluminum electrolytic ca-
pacitors are especially suitable for applications requiring high ca-
pacitance, low cost, and very small size. In fact, you’ll find these
capacitors in some of the most demanding applications, from
precision medical electronics and automobiles to the newest
personal computers and disk drives.
They operate over a broad temperature range and are available
in either blister pack or bulk.
RATINGS
PERFORMANCE SPECIFICATIONS
Rated Voltage
0.1 f to 1000 f
1000 f to 22,000 f
Comparison Z WV
Z @ - 25 C ( - 13 F)/
Z @ +20 C (+68 F)
Z @ - 40 C ( - 40 F)/
Z @ +20 C (+68 F)
DC Rated Voltage
Surge Voltage
Rated Voltage
6.3V to 16V
25V to 100V
2
ALUMINUM ELECTROLYTIC 6.3V to 100V
Capacitance Range: 0.1 f to 22,000 f
Tolerance:
Voltage Range: 6.3V to 100V
Operating Temperature Range:
Leakage Current: I
Capacitance Tolerance (M):
Dissipation Factor: measured at +20 C (+68 F),120H
Impedance Ratio at Low Temperature: 120H
Surge Voltage:
Load Life: 1000 12Hrs @ +85 C (+185 F),
Shelf Life: 1000 Hrs @ +85 C (+185 F),
C = Nominal Capacitance ( f)
V = Rated Voltage (V)
I = Leakage Current ( A)
3 minutes of applied voltage)
measured at +20 C (+68 F), 120H
at rated voltage
Leakage Current: Within values specified above
Dissipation Factor: Within 150% of specified value
Capacitance Change Max: See Table
no voltage applied
Leakage Current: Within 200% of specified value
Dissipation Factor: Within 150% of specified value
Capacitance Change Max: Within 20% of initial value
- 40 C to +85 C ( - 40 F to +185 F)
20%
NTE Electronics, Inc. D Voice (800) 631 - 1250 (973) 748 - 5089 D FAX (973) 748 - 6224 D http://www.nteinc.com
Within 30% of the initial value
Within 20% of the initial value
0.24
6.3
6.3
6.3
8
4
8
Values above plus 0.02 for each 1000 f
10
13
0.2
0.01CV + 3 A (measured after
10
10
Capacitance Change Max
3
6
16
20
0.17
16
16
2
4
20%
25
32
0.15
25
25
35
44
2
4
Z
0.12
35
50
63
35
2
4
50 - 80
0.10
Z
63
79
NEV, NEH SERIES
50 - 100
0.08
2
4
100
100
125
Z
MECHANICAL SPECIFICATIONS
CASE SIZE AND DIMENSIONS:
ORDERING INFORMATION
Series
Capacitance
Tolerance
Voltage
Lead Solderability:
Marking:
Recommended Cleaning Solvents:
NEV SERIES
NEH SERIES (Insulating Bar = Negative)
Insulating
Sleeve
D’ Ø = D Ø + 0.5 Max
d Ø
D’ Ø = D Ø + 0.5 Max
Meets the requirements of MIL - STD 202, Method 208
Consists of series type, nominal capacitance, rated
voltage, temperature range, anode and/or cathode
identification, vendor identification.
Methanol, isopropanol ethanol, isobutanol, petroleum
ether, propanol and/or commercial detergents. Halo-
genated hydrocarbon cleaning agents such as Freon
(MF, TF, or TC), trichloroethylene, trichloroethane, or
methylchloride are not recommended as they may
damage the capacitor.
35.0 Min
L’
L
18.0 Min
L’ = L + 1.0 Max at D Ø
L’ = L + 1.0 Max at D Ø
d Ø
5.0 Min
L’
L
NEV
35.0 Min
2.3 Max
47
Insulating
Sleeve
8.0
8.0
A 0.5
L’ = L + 2.0 Max at D Ø
L’ = L + 2.0 Max at D Ø
M
D Ø
D’ Ø
D Ø
D’ Ø
50
10.0
10.0