MCP6001T-I/OT Microchip Technology Inc., MCP6001T-I/OT Datasheet - Page 2

• Manufacturer Part Number: MCP6001T-I/OT
• Description: SINGLE 1.8V, 1MHZ OP, I TEMP
• Manufacturer: Microchip Technology Inc.

Specifications of MCP6001T-I/OT

• Amplifier Type: General Purpose, Low Power, Power, Rail-to-Rail, Single Supply
• Bandwidth: 1 MHz
• Common Mode Rejection Ratio: 76
• Current, Input Bias: 19 pA
• Current, Input Offset: ±1 pA
• Current, Output: ±30 mA
• Current, Supply: ±30 mA
• Number Of Amplifiers: Single
• Package Type: SOT23
• Slew Rate: 0.6
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 112 dB
• Voltage, Input: 1.5 to 2.1 V
• Voltage, Noise: 28 nV/sqrt Hz
• Voltage, Offset: +4.5 mV
• Voltage, Output, High: 1775 mV
• Voltage, Output, Low: 1775 mV
• Voltage, Supply: 1.8 to 6 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

MCP6001/1R/1U/2/4
1.0
Absolute Maximum Ratings †
V
Current at Analog Input Pins (V
Analog Inputs (V
All Other Inputs and Outputs ......... V
Difference Input Voltage ...................................... |V
Output Short Circuit Current .................................Continuous
Current at Output and Supply Pins ............................±30 mA
Storage Temperature....................................–65°C to +150°C
Maximum Junction Temperature (T
ESD Protection On All Pins (HBM; MM) .............. ≥ 4 kV; 200V
DC ELECTRICAL SPECIFICATIONS
DS21733H-page 2
Electrical Characteristics: Unless otherwise indicated, T
R
Input Offset
Input Offset Voltage
Input Offset Drift with Temperature
Power Supply Rejection Ratio
Input Bias Current and Impedance
Input Bias Current:
Input Offset Current
Common Mode Input Impedance
Differential Input Impedance
Common Mode
Common Mode Input Range
Common Mode Rejection Ratio
Open-Loop Gain
DC Open-Loop Gain (Large Signal)
Output
Maximum Output Voltage Swing
Output Short Circuit Current
Power Supply
Supply Voltage
Quiescent Current per Amplifier
Note 1:
DD
L
= 10 kΩ to V
– V
Industrial Temperature
Extended Temperature
2:
SS
ELECTRICAL
CHARACTERISTICS
........................................................................7.0V
MCP6001/1R/1U/2/4 parts with date codes prior to December 2004 (week code 49) were tested to ±7 mV minimum/
maximum limits.
All parts with date codes November 2007 and later have been screened to ensure operation at
V
Parameters
DD
L
IN
, and V
= 6.0V. However, the other minimum and maximum specifications are measured at 1.8V and 5.5V.
+, V
IN
–) †† ........ V
OUT
≈ V
IN
DD
+, V
J
/2 (refer to
) ......................... .+150°C
SS
SS
IN
–) .....................±2 mA
– 1.0V to V
– 0.3V to V
ΔV
V
CMRR
PSRR
OL
Z
V
Sym
V
OS
Z
V
Figure 1-1
A
I
I
DIFF
CMR
I
I
I
I
OS
SC
CM
, V
OS
DD
OL
Q
B
B
B
/ΔT
OH
DD
DD
DD
A
+ 1.0V
+ 0.3V
– V
V
V
and
SS
SS
SS
A
Min
-4.5
1.8
60
88
50
—
—
—
—
—
—
—
—
—
—
= +25°C, V
|
− 0.3
+ 25
Figure
1-2).
10
10
1100
±2.0
±1.0
±1.0
Typ
±23
100
112
DD
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of
the device at those or any other conditions above those
indicated in the operational listings of this specification is not
implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
†† See Section 4.1.2 “Input Voltage and Current Limits”.
86
19
76
±6
—
—
—
—
13
13
||6
||3
= +1.8V to +5.5V, V
V
V
DD
DD
Max
+4.5
170
6.0
—
—
—
—
—
—
—
—
—
—
—
—
+ 0.3
– 25
µV/°C
Units
Ω||pF
Ω||pF
SS
mV
mV
mA
mA
dB
pA
pA
pA
pA
dB
dB
µA
V
V
= GND, V
© 2008 Microchip Technology Inc.
V
T
V
V
T
T
V
V
V
V
V
0.5V Input Overdrive
V
V
Note 2
I
O
A
A
A
CM
CM
CM
CM
DD
OUT
CM
DD
DD
DD
= -40°C to +125°C,
= 0, V
= +85°C
= +125°C
= 5V
= 1.8V
= 5.5V
= -0.3V to 5.3V,
= V
= 5.5V,
= V
= V
= V
CM
= 0.3V to V
SS
SS
SS
SS
= V
DD
Conditions
(Note 1)
DD
= 5.5V, V
/2, V
DD
L
– 0.3V,
= V
CM
DD
= 5V
/2,