CW3300B Chemtronics, CW3300B Datasheet - Page 4

• Manufacturer Part Number: CW3300B
• Description: Protective Coating; 0.9; Blue
• Manufacturer: Chemtronics
• Type: Conformal Protectiver

Specifications of CW3300B

• Dispensing Method: Pen
• Primary Type: Coating
• Lead Free Status / Rohs Status: RoHS Compliant part Hazardous Materials

ITW CHEMTRONICS
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Clear, green or blue colored paint
Odor: Characteristic
pH: NA
Vapor Pressure: 78 mmHg @ 20°C
Vapor Density: >1
(Air = 1)
SECTION 10: STABILITY AND REACTIVITY
Stability: This product is stable.
Incompatibility: Do not mix strong oxidizers, mineral and organic acids, bases, caustics, amines and alkali contamination.
Products of Decomposition: Decomposition may release carbon monoxide, carbon dioxide, oxides of nitrogen monomers and smoke. Depending on conditions, some
highly reactive peroxides may be formed.
Hazardous Polymerization: Will not occur.
Conditions to avoid: NA
SECTION 11: TOXICOLOGICAL INFORMATION
Ingredients
Propylene Glycol Methyl Ether Acetate
n-propyl acetate
Methyl ethyl ketone
Acrylic Resin
Cancer Information: No ingredients listed as human carcinogens by NTP or IARC
Reproductive effects: none
SECTION 12: ECOLOGICAL INFORMATION
Environmental Impact Information
Avoid runoff into storm sewers and ditches which lead to waterways. Water runoff can cause environmental damage.
REPORTING
US regulations require reporting spills of this material that could reach any surface waters. The toll free number for the US Coast Guard National Response Center is:
1-800-424-8802
SECTION 13: DISPOSAL CONSIDERATIONS
Dispose of in accordance with all federal, state and local regulations. Water runoff can cause environmental damage.
SECTION 14: TRANSPORTATION INFORMATION
Air:
Ground: Consumer Commodity
SECTION 15: REGULATORY INFORMATION
SECTION 313 SUPPLIER NOTIFICATION
This product contains no toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To- Know Act of 1986
(40 CFR 372).
This information should be included on all MSDSs copied and distributed for this material.
TOXIC SUBSTANCES CONTROL ACT (TSCA).
All ingredients of this product are listed on the TSCA Inventory.
WHMIS: Class B2: Class D2B
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all of the information required by the CPR.
SECTION 16: OTHER INFORMATION
Normal ventilation for standard manufacturing practices is usually adequate. Local exhaust should be used when large amounts are released.
To the best of our knowledge, the information contained herein is accurate. However, all materials may present unknown hazards and should be used with caution. In
particular, improper use of our products and their inappropriate combination with other products and substances may produce harmful results which cannot be
anticipated. Final determination of the suitability of any material is the sole responsibility of the user. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that may exist.
Shipping Name
Paint
Proper
ORM-D
®
Conditions to Avoid: Avoid heat, sparks, open flame and strong oxidizing conditions.
NA
LD50
(rat) Oral
8532 mg/kg
9300 mg/kg
2700 mg/kg
UN1263
UN Number
-
Note: This MSDS is applicable to date codes of 2196 and later.
Teratogenic effects: none
ORM-D
Class
3
(rbt) Dermal
>5000 mg/kg
5000 mg/24H MLD
NA
5000 mg/24H MLD
LD50
Sub.
Risk
-
-
Page 2 of 2
II
Pkg.
Group
-
Solubility in Water: Appreciable
Specific Gravity: 0.9
Evaporation Rate: >1
(Butyl acetate=1)
Boiling Range: 175-284°F (79 – 140C)
Percent Volatile: 70%
5000 ppm/4H
LC50
(rat) Inhalation
>4300 ppm
NA
NA
Hazard
Label
Flammable
Liquid
ORM-D
Mutagenic effects: none
1 73.150
Pkg.
Instr.
305
MSDS #4004
Quantity
Max.
1 L
5 L